background image

HELPLINE NO 08448012949

13

OrIgINaL INstructIONs

MaINtENaNcE

remove the plug from the socket before 

carrying out any adjustment, servicing or 

maintenance.

Your power tool requires no additional lubrication 

or maintenance. There are no user serviceable 

parts in your power tool. Never use water or 

chemical cleaners to clean your power tool. Wipe 

clean with a dry cloth. Always store your power 

tool in a dry place. Keep the motor ventilation 

slots clean. Keep all working controls free of dust. 

Occasionally you may see sparks through the 

ventilation slots. This is normal. 

If the supply cord is damaged, it must be replaced 

by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard. 

trOuBLEsHOOtINg

1. If your router will not operate, check the power 

at the mains plug.

2. If a fault cannot be rectified, return the drill to 

an authorized dealer for repair. 

PLug rEPLacEMENt (uk & 

IrELaND ONLy)

Your power tool is supplied with a fitted plug, 

however if you need to fit a new plug follow the 

instruction below.

IMPOrtaNt

The wires in the mains lead are colored in 

accordance with the following code:

Blue = Neutral   Brown = Live

As the colors of the wires in the mains lead of this 

appliance may not correspond with the coloured 

markings identifying the terminals in your plug, 

proceed as follows. The wire which is coloured 

blue must be connected to the terminal which 

is marked with N. The wire which is coloured 

brown must be connected to the terminal which is 

marked with L.

warNINg:

 Never connect live or neutral wires to the 

earth terminal of the plug. Only fit an approved 

BS1363/A plug and the correct rated fuse.

Note: If a moulded plug is fitted and has to be 

removed take great care in disposing of the 

plug and severed cable, it must be destroyed to 

prevent engaging into a socket.

Summary of Contents for PRT1204.1

















Reviews: