T
TR
RO
OU
UB
BL
LE
ES
SH
HO
OO
OT
TIIN
NG
G
W
WA
AR
RN
NIIN
NG
G::
If fan fails to start, please follow the procedure listed below:
1. Check the incoming supply for proper voltage.
2. Ensure that the electrical service to the fan is locked in the
“OFF” position.
3. Consult wiring diagram to ensure proper connection.
4. Use a meter to test the continutity across the fan motor leads.
5. If the motor leads show continuity, rewire the fan and timer.
6. Turn on the electrical supply and restart.
7. Check to be certain that fan starts.
8. If fan fails to start:
a) Ensure that the electrical service to the fan is locked in
the “OFF” position.
b) Remove the timer from the circuit.
c) Connect the incoming power supply directly to the fan motor.
d) Turn on power to fan.
9. If fan fails to start, please contact technical support @
1-800-779-4021.
R
RE
EC
CO
OM
MM
ME
EN
ND
DE
ED
D M
MA
AIIN
NT
TE
EN
NA
AN
NC
CE
E
C
CA
AU
UT
TIIO
ON
N::
1. Before servicing or cleaning, ensure that the electrical
service to the fan is locked in the “OFF” position.
2. Fan bearings are sealed. No additional lubrication is necessary.
3. Periodic inspection, based upon usage, should be performed
to ensure that the fan impeller is not obstructed. The fan
should be inspected a minimum of every six (6) months.
4. Excessive fan noise or vibration may indicate an obstructed
impeller.
5. To inspect and clean impeller:
a) Ensure that the electrical service to the fan is locked in
the “OFF” position.
b) Remove the duct from the fan inlet and remove any
obstruction from the impeller.
c) Reconnect the duct to the fan.
d) Turn power supply on.
DVK-T
DR
YER I&M-0805
USA
www.continentalfan.com
Canada
www.aeroflo.com
C
Co
on
nttiin
ne
en
ntta
all F
Fa
an
n M
Ma
an
nu
uffa
ac
cttu
urriin
ng
g IIn
nc
c..
203 Eggert Rd.
Buffalo, NY 14215
Tel: 716-842-0670 Toll: 800-779-4021 Fax: 716-842-0611
A
Ae
erro
offllo
o IIn
nc
c..
12-205 Matheson Blvd. East
Mississauga, ON L4Z 3E3
Tel: 905-890-6192 Toll: 800-779-4021 Fax: 905-890-6193
S
SP
PR
RIIN
NG
G W
WO
OU
UN
ND
D IIN
NT
TE
ER
RV
VA
AL
L T
TIIM
ME
ER
R
The C
CT
T--1
10
00
0 0-1 hour spring wound interval timer is
easily installed in a standard electrical box. This
spring wound timer will automatically turn the fan off
after a preset period. For automatic operation, turn
timer clockwise to desired drying time. Timer will
turn “OFF” at the end of preset timed period.
T
TIIM
ME
ER
R IIN
NS
ST
TA
AL
LL
LA
AT
TIIO
ON
N
Ensure that the electrical service to the fan is locked in the
“OFF” position. Wiring must be done in accordance with all
applicable codes and standards. The unit must be properly
grounded. Ensure the supply voltage corresponds to the volt-
age listed on the name plate.
A
AT
T S
SW
WIIT
TC
CH
H L
LO
OC
CA
AT
TIIO
ON
N
1. Remove wall plate and disconnect switch from electrical
box.
2. Strip wire ends ½ inch long using strip gauge on back of
timer.
3. Follow the enclosed wiring diagram. Insert the stripped wire
ends under the pressure plate of terminal screws on the side
of timer (terminal screws provide in plastic bag).
Screw
down tightly. Insert wired timer into a standard electrical box
with “TOP” (indicated on front of timer) in proper position and
fasten timer to junction box using the screws provided.
4. Slip metal dial plate over threaded extension with “OFF”
position facing up.
5. Fasten metal dial plate securely to timer with stamped nut
provided..
W
WIIR
RIIN
NG
G P
PR
RO
OC
CE
ED
DU
UR
RE
ES
S
Refer to wiring diagram.
W
WA
AR
RR
RA
AN
NT
TY
Y
This warranty supersedes all prior warranties.
D
DV
VK
K1
10
00
0B
B fans are warranted against defects in material and workmanship for a period of five years from date of purchase. All
other products are warranted for a period of one year from date of purchase.
W
WA
AR
RR
RA
AN
NT
TY
Y D
DO
OE
ES
S N
NO
OT
T A
AP
PP
PL
LY
Y T
TO
O::
• Shipping damage, whether concealed or visible. Claims must be filed with the carrier.
• Damage caused by improper installation, wiring, or incorrect electrical voltage.
• Materials that have been modified, altered or disassembled.
• Damage caused by corrosion, abrasion or severe temperature.
• Materials that have had the identification labels removed or altered.
• Materials that have been subjected to improper maintenance, abuse, misuse, abnormal usage or accident.
No other warranties, expressed, implied or written shall apply to this product. Vendor will not be responsible for any consequen-
tial or incidental damages, loss of property, revenues or profit, cost of removal, installation, or reinstallation, personal damage or
loss of life, or for any breach of warranty, regardless of how caused.
All warranty claims must be processed through point of purchase..
