CEWAL PTE2.0 Installation And Use Manual Download Page 2

AVVERTENZA:  

Se  l’installazione  del  PTE2.0  viene  effettuata  in  sostituzione  di  un  precedente 
termostato  con  alimentazione  a  220V,  dovranno  essere  utilizzati  solo  i  due 
conduttori elettrici dell’impianto che provengono dall’apparecchio da comandare. È 
importante che i rimanenti conduttori non utilizzati vengano accuratamente isolati. 

 

3 – INSERIMENTO DELLE PILE 

Dopo  l’installazione  dell’apparecchio,  aprire  lo  sportello  di  accesso  alle  pile 

  tirando 

l’apposita linguella. Inserire due pile alcaline (importante!) formato stilo tipo LR6 rispettando 
le polarità indicate nello schema riportato nel vano batterie. 

 

4  – REGOLAZIONE DELL’ORA 

Far girare il disco di regolazione   in senso orario fino a far coincidere l’indicazione oraria 
segnata sul disco   con la tacca di riferimento  . 

 

5 –  REGOLAZIONE DELLE TEMPERATURE 

Si possono regolare due livelli di temperatura tra +6°C e +30°C. 

Temperatura confort

:

  

È  la  temperatura  che  normalmente  si  desidera  mantenere  durante  le  ore  di  presenza  in 
casa.  La  temperatura  comfort  si  regola  posizionando  l’indice  della  manopola 

  in 

corrispondenza della temperatura desiderata.  

Temperatura ridotta: 

 

È la temperatura, normalmente più bassa di quella confort, abitualmente  desiderata durante la 
notte o durante le ore di assenza. La temperatura ridotta si regola posizionando l’indice della 
manopola 

  in  corrispondenza  della  temperatura  desiderata.  Si  consiglia  di  regolare  la 

temperatura ridotta a un valore di 3 - 5°C inferiore a quello della temperatura confort. 

 

NOTA

: la risposta dei relè alla programmazione fatta (click di scatto) avviene con un ritardo 

di qualche decina di secondi.  

 

6 –  SCELTA DEL REGIME DI FUNZIONAMENTO

 

Il selettore   permette di scegliere il regime di funzionamento: 

  Regime  automatico:  commutazione  automatica  tra  le  temperature  confort  e  ridotta 

secondo le fasce orarie programmate tramite l’orologio.  

  Regime  confort permanente:  mantiene  il livello  della  temperatura  confort  selezionato 

con la manopola  . 

   Regime antigelo: permette di mantenere  permanentemente una temperatura minima 

di 4 °C durante le assenze prolungate. Questo protegge le tubature dell’abitazione dai 
rischi del gelo. Per maggiore garanzia questa temperatura non è regolabile. 

 

7 – PROGRAMMAZIONE DELL’OROLOGIO 

L’orologio  del  PTE2.0  consente  di  programmare  le  fasce  orarie  corrispondenti  alle 
temperature confort e ridotta. La programmazione è estremamente agevole: 

-  posizionare i cavalieri   verso l’esterno del disco per i periodi di temperatura confort  
-  posizionare i cavalieri   verso l’interno del disco per i periodi di temperatura ridotta  

La programmazione così effettuata rimarrà inalterata tutti i giorni purché il selettore 

 sia 

impostato sulla posizione orologio. 

NOTA

:  l’impianto  verrà  attivato  dal  cronotermostato  all’ora programmata.  Sarà  opportuno 

quindi in fase di programmazione tener conto del tempo necessario all’impianto per portare 
in temperatura l’ambiente.  

 

8 – CARATTERISTICHE TECNICHE 

-

 

Campo di regolazione della temperatura confort e ridotta: da +6°C a +30°C 

-

 

  An 4°C 

-

 

  Differenziale statico: 0,5°C 

-

 

  Alimentazione: 2 pile alcaline  tipo LR6 (formato stilo) 

-

 

  Durata delle pile: circa un anno 

-

 

  Uscita: contatto in commutazione senza potenziale 

-

 

  Portata:  

8A/250 VAC cos φ =1 (carico resistivo) 
2A/250 VAC cos φ =0,6 (carico induttivo) 

-

 

Temperatura di funzionamento: da 0°C a +50°C 

-

 

Temperatura di stoccaggio: da –10°C a +60°C 

-

 

Umidità: max 90% a 20°C 

-

 

IP30 

-

 

Raccordi con morsetti a vite: 

Filo rigido fino a 2,5 mm

2

 

Filo flessibile fino a 1,5 mm

2

 

 

9 – CONFORMITÀ ALLE NORME 

-

 

- EN 60730 

-

 

- BT 2006/95/CE 

-

 

- EMC 2004/108/CE 

 

10 – PRESCRIZIONI DI SICUREZZA 

Prima  di  collegare  il  cronotermostato  accertarsi  che  la  tensione  di  alimentazione  del 
CARICO  UTILIZZATORE  da  comandare  NON  SIA

 

COLLEGATA.  Verificare  inoltre  che  il 

carico sia compatibile con le caratteristiche di portata dei contatti (vedere dati tecnici). 

ATTENZIONE: le operazioni di collegamento descritte nel presente foglio istruzioni vanno 
eseguite  esclusivamente  da  personale  specializzato  o  dall’installatore,  rispettando 
scrupolosamente le norme di sicurezza e le disposizioni di legge vigenti. 

WARNING:  

If  the  PTE2.0  is  replacing  a  previous  thermostat  with  a  220V  supply,  just  the  two 
electric  leads  coming  from  the  appliance  to  be  controlled  must  be  connected.  The 
remaining leads, that are no more used, must be carefully isolated. 

 

 

3 – FITTING THE BATTERIES 

After  installing  the  appliance,  open  the  flap  to  the  battery  compartment 

  by  pulling  the 

tab.  Fit  in  two  alkaline  batteries  (important!)  type  LR6,  respecting  the  polarity  indicated 
inside the battery compartment. 
 

4  – REGULATING THE TIME ON THE CLOCK  

Turn the regulation disk   in a clockwise direction until the actual time, shown on the disk  , 
matches with the time reference notch

 

 

5 –  REGULATING THE TEMPERATURES 

Two heating temperatures can be set b6°C and +30°C. 

Comfort temperature

 

This is the temperature you normally want to have into the room when you are at home. 
Use knob   to regulate it to the desired level.  

Reduced temperature:

 

 

 

This is the temperature, usually lower than the comfort one, you normally want to have into 
the room when you are not at home. Use knob   to regulate it to the desired level.  

We advise setting the reduced temperature 3 or 5°C lower than the comfort temperature. 

 

NOTA

: the response of the relay to the programming (audible click) comes with a delay of a 

few tens of seconds.  

 

6 –  CHOOSING THE OPERATING REGIME

 

The selector   allows choosing the operating regime: 

  Automatic:  automatic  switch  over  between  comfort  and  reduced  temperature 

according to the programmed time bands on the clock.  

  Permanent comfort: keeps the comfort temperature set using knob  . 

  Antifreeze:  keeps  a  minimum  permanent  temperature  of  around  4°C  during  long 

periods  of  absence.  This  protects  the  plumbing  of  the  house  against  the  risk  of 
freezing. For greater guarantee this temperature cannot be regulated. 

 

7 – PROGRAMMING THE SECTORS ON THE CLOCK 

The  PTE2.0  clock  allows  programming  time bands  for  comfort  and  reduced  temperature. 
Programming is extremely easy: 

-  place the sector   towards the outside of the disk for comfort temperature periods  
-  place the sector   towards the inside of the disk for reduced temperature periods 

This  program  will  then  be  repeated  every  day  if  the  selection  switch 

  remains  on  the 

clock position. 

NOTE: 

the  heating  system  will  start  working  at  the  programmed  time.  Therefore    we 

recommend anticipating appropriately the start and stop of the comfort period so that the 
system reaches the desired temperature on time.  

 

8 – TECHNICAL FEATURES 

-

 

Temperatures regulation range, comfort and reduced: from +6°C to +30°C 

-

 

Antifreeze: +4°C 

-

 

Static differential: 0,5°C 

-

 

Power supply: 2 AA batteries, type LR6 

-

 

Batteries life: approximately one year. 

-

 

Output: switch over contact without potential. 

-

 

Delivery:  

8 A/250 VAC cos φ =1 (resistive load) 
2 A/250 VAC cos φ =0,6 (inductive load) 

-

 

Working temperature: between 0°C and +50°C 

-

 

Storage temperature: between –10°C and +60°C 

-

 

Humidity: max. 90% at 20°C 

-

 

IP30 

-

 

Joint with screwed terminals: 

Stiff wire up to 2.5 mm

2

 

Flexible wire up to 1.5 mm

2

 

 

9 – CONFORMITY TO STANDARDS 

-

 

- EN 60730 

-

 

- BT 2006/95/CE 

-

 

- EMC 2004/108/CE 

 

10 – SAFETY RECOMMENDATIONS 

CHECK  THAT  THE  POWER  IS  DISCONNECTED  on  the  USER  BEING  CONTROLLED 
before connecting the chronothermostat. Check that the power input is compatible with the 
output on the contacts (see the technical data). 

ATTENTION:  only  specialized  electricians  or  authorized  installers  must  carry  out  the 
electric  connection  instructions  given  in  this  leaflet,  in  full  observance  of  the  safety 
instructions and current applicable legislation. 

 

X

75

42

8-

Reviews: