background image

Instruction Handbook                          PFP-13hpHND-EM-HP80  

- 6 -

 

 C.E.T. Fire Pumps Mfg. This handbook is subject to change without notice, 

Contact your local C.E.T. dealer or C.E.T. direct to ensure you have the latest version.

 

o

 

NEVER run the pump for more than one minute without water.  

o

 

NEVER run the engine without the proper amount of oil in the engine. 

o

 

NEVER alter the engine and/or the pump even partially.  

 

 

Signs and Symbols 

 

 This warning symbol means that not following the attached note will put at 

risk  the  security  of  the  personnel  operating  near  the  pump.  The  words 

“danger”, “warning” and “caution” are used 

for levels of risk. 

 

This symbol means that it is mandatory to read and understand this handbook 

as well as the operation manual from the engine manufacturer, BEFORE you 

start the engine.  

 

This symbol represents the risk of injury from high temperature surfaces. 

 

This symbol represents the risk of intoxication from dangerous gases, such 

as carbon monoxide. 

 

This symbol represents the risk of injury caused by moving parts.  

 

This symbol represents the hazards of handling dangerous material such as 

gasoline or diesel. 

 

CAUTION 

 

Summary of Contents for PFP-13hpHND-EM-HP80
























Reviews: