background image

Rev G 

Page 4 

5/9/2017 

Copyright © 2017 by Certified Cirus Control Systems.   All Rights Reserved. No part of this material may 
be reproduced in any form without the express written permission of Certified Cirus Control Systems 

 

Revision Level of this Manual 

Rev Letter 

Effective Date  

Contents 

 

2/14/12 

 

Initial Release 

 

3/27/13 

 

Replaced trim pot calibration with engage/set point 

 

5/9/17   

 

Added 12 or 24 volt settings 

Package Contents 

 

A complete 

SCMC 

TM

 control system contains the following items: 

 

1)

 

SCMC 

TM

 control unit; 

2)

 

Power cable (MK-1003); 

3)

 

PWM Hydraulic control cable (SF-1005); 

4)

 

Valve hydraulic control cable (MK-2005); 

5)

 

Trigger cable (JP-1002); 

6)

 

This manual; 

 
If any of these items are missing, please contact your distributor for replacement parts. 
 

Functional Overview 

SCMC

 TM

 is a manually regulated plow controller which adjusts the “contact weight” (down 

force) that the moldboard of a snowplow exerts on a road surface.  The system decreases or 
increases the contact weight of the snowplow depending on the position of the Set Point.

 

This controller is able to transfer weight from the truck to the plow to increase the 
plowing capability for packed snow/ice.  (This feature requires a snowplow designed for 
down pressure and the proper size truck).
 
 

Normal Operation: 

1.

 

Turn the power switch on. 

2.

 

To activate the system turn the engage switch to “ON” or set the Trigger. 

3.

 

Turn the Set Point dial to reduce or increase the contact weight.   

 
 
 
 
 
 
 

Summary of Contents for SCMC










Reviews: