background image

 

HIGH SPEED INTERNET MODEM FAMILY 

 

 CH2124 

Send/Retrieve 

Email.  2 I/O Ports 2400bps. 

 CH2160 

Send/Retrieve 

Email.  2 I/O Ports, V.90. 

 

 

2005 Cermetek Microelectronics, Inc. 

Page 1 

Document No. 607-0017 Revision I1 (05/05)

 

FEATURES 

  Replaces conventional modems using the world 

wide web for communication. 

  Transparent internet operations of Point-to-Point 

Protocol (PPP), Password Authentication Protocol 
(PAP) and Challenge Authentication Protocol 
(CHAP) to connect to the Internet. 

  Built-in TCP/IP and SMTP to send emails, TCP/IP 

and POP3 to retrieve and/or delete emails. 

  On Demand and I/O pin event driven email 

transmission and retrieval. 

 Send/Retrieve 

email. 

  Retrieve select individual message. 

  Programmable using serial interface. 

  Remote programming using PSTN. 

  Resident modem supports: V.90, V.34bis, V.34, 

V.22bis, V.22A/B V.23, V.21, Bell 212A and 103, 
(depending on model) and can be used in 
conventional modem mode. 

  Error correcting: V.42 LAPM, MNP 2-4 and MNP10 

(CH2160). 

  Automatic baud rate adaptability utilizing speed 

sensing, flow control and data buffers. 

  Serial interface, V.24 (EIA 232-E), 5 volts. 

  NVRAM for stored modem (S-Registers) profiles. 

 Cermetek 

@T

®

 AT-like Commands. 

  Built-in DAA with 1500 VAC RMS isolation 2122V 

peak surge protection. 

  UL 1950 and CSA C22.2 950 (Third Edition) Listed, 

reference UL File E104957. 

  FCC Part 68 Approved/Industry Canada CS-03 Part 

I approvable. 

  Pin-for-Pin compatible family. 

  +5 Volt operation. 

  Small size: 1.35” x 1.97” x 0.55” (nominal). 

  Low Cost 2400bps version (CH2124). 

  Use with any Non-proprietary commercial or private 

ISP. 

 Cermetek’s 

iModem Network

 ISP has 1000s of 

local access numbers world wide. 

  Failsafe back up 1-800 access number, auxiliary 

and alternative telephone numbers available. 

  1 year free trial subscription to 

iModem Network

 

ISP provided with each iModem. 

 iNetWizard

®

 Windows based programming aid 

available free-of-change. 

INTRODUCTION 

Direct machine-to-machine interaction represents the 
next logical extension of the internet.  Cermetek internet 
modem (iModem) products are designed to exploit the 
internet to facilitate the utilization of machine-to-
machine interactions.  Using email, information can 
easily be transferred between systems and can be 
transmitted/retrieved at will.  Internet email provides low 
cost, near real time multi-path communication. 

 

Replacing conventional modems and long distance 
telephone lines with local access internet connections 
reduces fixed asset and maintenance costs, limits 
communication expenses and saves money. 
 
 

USER FRIENDLY INTERFACE LAYER 

All Cermetek iModem products contain a user friendly 
interface layer that provides the user transparent 
access to the internet.  This interface layer, consisting 
of various 

@T

®

 macro commands, has the look and feel 

of conventional modem AT commands.  With the 

@T

®

 

macro commands the user can direct the iModem to 
compose, edit/modify, send, retrieve and delete email 
messages.  Internet and email activity status is reported 
via the iModem’s V.24 (EIA 232-E) serial interface. 
 
The CH2124/60 products are the first generation 
internet enabled devices.  These products excel at 
sending and retrieving modest amounts of data.  Email 
messages of approximately 125 ASCII characters in 
length can be stored in internal Flash ROM for later 
transmission.  Emails of larger length can be retrieved. 
 
The CH2124/60 products are ideal for very low cost 
controller applications and in applications where limited 
data transfer is required.

 

 
 

OVERVIEW OF THE CH21XX iMODEM

 

A conceptual representation of the iModem in an 
embedded environment is presented in Figure 1.  As 
can be seen in this figure, the iModem requires the 
input of various internet parameters to function properly: 
user name, user ID, user password, ISP telephone 
number, ISP mail server address/name, local email 
address/name, destination email address and user 
specified email message/input port status. 
 
 

Summary of Contents for CH2124



















Reviews: