Century Helicopter Products Predator 60/70 SE Instruction Manual Download | Manualshive

Page: 9 / 20

background image

17mm

Standoff x 4

Attach the X Frame to the lower side frames first using M3x8
Socket screws and locknuts at the lower hole on a flat surface.
Attach to the upper frames with M3x25 Socket screws, apply
threadlock to the holes on the upper side frames.

#HW6115A
Rear Lower
Frames

#HW6117 Rear X Frame

X-Frame

Standoff x 2

26mm Threaded Standoff

M3x25
Socket
Screws

Before the main gear assembly can be inserted, make sure
that the M10x14x3.5 spacer is positioned on top of the lower
main shaft bearing. It will simply self align in the block.
Remember, do not locktight any bolts on the clutchbell or
starting shaft bearing blocks until the engine is installed.

#HW6054 Spacer

Slide the autohub for the slipper drive from the bottom of the
main gear. Attach with M3 button head screws and tightening
evenly. Insert the slipper cap assembly, capturing the o-ring
under the cap against the autohub.

#HW6001 Main
Shaft Pin & M4x4
Set Screws x 2

#M3x8 Button
Head Screw x 4

Thread the slipper cap onto the sleeve until the holes align
together. Insert two M4x4 set screws at 180 degrees apart and
tighten gently. Later when the main shaft pin is attached, these
can be removed and locktighted in place.

#HW6001
M4x4 Set
Screw x 2

#HI6058K

Slipper Cap &

Sleeve

#HI6058L
Slipper O-Ring

#HI6058P
Autohub -
Slipper

#HI6056 Main Gear
90T - Slipper Drive

#HI6058M

Autohub - Inner

Gear CT Drive

#HI6058B

Machined Inner

Gear 70T - CT

Drive

M3x6 Flat Head
Screws x 4

Install inner gear autohub from the bottom side the inner (tail)
gear using threadlock. Attach with M3 flat head screws and
tightening evenly. Note the autohub is pre-assembled.

M3x6 Flat Head
Screws x 4

Install outer gear autohub from the bottom side the outer main
gear using threadlock. Attach with M3 flat head screws and
tightening evenly. Overtigtening these screws could touch the
upper side frames. **Use heavy bearing grease only in auto
rotation hub.

#HI6058N
Autohub - Outer
Gear CT Drive

#HI6058C
Machined Outer
Gear 90T - CT Drive
#HI6058D
Machined Outer
Gear 93T - CT Drive

SE & Max

60/70 Kit

38

42

9

37

39

40

41

Heavy Bearing
Grease Only!

«
...
7
8
9
10
11
...
»

Summary of Contents for Predator 60/70 SE





















Reviews:

No comments

Related manuals for Predator 60/70 SE

Brand: Minicraft Models Pages: 4

minideices 17865

Brand: Lansay Pages: 2

G2579 The Incredibles

Brand: Fisher-Price Pages: 10

Brand: Fisher-Price Pages: 2

Pennsylvania 6-8-6 Bantam Turbine Steam Freight...

Brand: Rail King Pages: 24

Brand: Fisher-Price Pages: 16

MH-60K interior S.A.

Brand: Eduard Pages: 4

Modern Metro Kitchen 8797

Brand: Step2 Pages: 12

Brand: ItsImagical Pages: 10

spongebob squarepants 3818

Brand: LEGO Pages: 84

Brand: Multiplex Pages: 28

Brand: Radica Games Pages: 2

Edge 540 74" 30cc

Brand: Vantex Pages: 12

Brand: REVELL Pages: 8

Brand: electrifly Pages: 24

DreamWorks DINOTRUX TY RUX

Brand: Mega Construx Pages: 24

Brand: Tower Hobbies Pages: 4

Brand: Tower Hobbies Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands