Century Helicopter Products Hummingbird Elite 3D Pro Assembly And Instruction Manual Download Page 1

Page: 1 / 12

Hummingbird

Elite 3D Pro

This Super-Micro R/C helicopter has the most advanced capabilities and is considered

top-of-the-line. 120 degree eCCPM control, collective main and tail rotors, torque tube tail

drive and brushless motor ensure top performance.

MAX MAIN ROTOR RPM

3000

RECOMMENDED MOTOR:

HIMAX 4100

MAIN ROTOR DIAMETER:

520mm

LENGTH:

485mm

WEIGHT:

360-380g with electronics and battery

Century Helicopter Products

Designed and Developed in USA

SPECIFICATIONS

Fax: (408) 451-1156

Web:www.centuryheli.com

Century Helicopter Products

1740-C Junction Ave.

San Jose, CA 95112

Assembly Kit

Instruction

Manual

Summary of Contents for Hummingbird Elite 3D Pro













Search results

Summary of Contents for Hummingbird Elite 3D Pro

Reviews:

Related manuals for Hummingbird Elite 3D Pro

Brands by name

Popular brands

Century Helicopter Products Hummingbird Elite 3D Pro, Assembly And Instruction Manual

Search results

Summary of Contents for Hummingbird Elite 3D Pro

Reviews:

Related manuals for Hummingbird Elite 3D Pro

Brands by name

Popular brands