Central Pneumatic 95810 Owner'S Manual & Safety Instructions Download Page 16

26541 Agoura road  •  Calabasas, CA 91302  •  1-888-866-5797

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality 
and durability standards, and warrants to the original purchaser that this product is free from 
defects in materials and workmanship for the period of 90 days from the date of purchase. 
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence 
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, 
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, 
injuries to persons or property, or for incidental, contingent, special or consequential damages 
arising from the use of our product. Some states do not allow the exclusion or limitation of 
incidental or consequential damages, so the above limitation of exclusion may not apply to you. 
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR 
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with 
transportation charges prepaid. Proof of purchase date and an explanation of the complaint 
must accompany the merchandise. If our inspection verifies the defect, we will either repair or 
replace the product at our election or we may elect to refund the purchase price if we cannot 
readily and quickly provide you with a replacement. We will return repaired products at our 
expense, but if we determine there is no defect, or that the defect resulted from causes not 
within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also 
have other rights which vary from state to state.

Summary of Contents for 95810

















Reviews: