background image

Page 7

SKU 98676

For technical questions, please call 1-800-444-3353.

grOuNDINg

 

TO prEVENT 

ELEcTrIc SHOcK 

AND DEATH FrOM 

INcOrrEcT grOuNDINg 

WIrE cONNEcTION: 

Check with a qualified 

electrician if you are in doubt 

as to whether the outlet is 

properly grounded.  Do not 

modify the power cord plug 

provided with the tool.  Never 

remove the grounding prong 

from the plug.  Do not use the 

tool if the power cord or plug 

is damaged.  If damaged, have 

it repaired by a service facility 

before use.  If the plug will not 

fit the outlet, have a proper 

outlet installed by a qualified 

electrician.

grounded Tools: Tools with Three 

prong plugs

3-prong plug and Outlet

1.  Tools marked with “Grounding Re-

quired” have a three wire cord and 

three prong grounding plug.  The 

plug must be connected to a properly 

grounded outlet.  If the tool should 

electrically malfunction or break 

down, grounding provides a low 

resistance path to carry electricity 

away from the user, reducing the risk 

of electric shock.  

(See 3-prong plug 

and Outlet.)

The grounding prong in the plug is 

2. 

connected through the green wire in-

side the cord to the grounding system 

in the tool.  The green wire in the cord 

must be the only wire connected to 

the tool’s grounding system and must 

never be attached to an electrically 

“live” terminal.  

(See 3-prong plug 

and Outlet.)

The tool must be plugged into an 

3. 

appropriate outlet, properly installed 

and grounded in accordance with all 

codes and ordinances.  The plug and 

outlet should look like those in the 

preceding illustration.  

(See 3-prong 

plug and Outlet.)

EXTENSION cOrDS

Grounded

1. 

 tools require a three wire 

extension cord.  

Double Insulated

 

tools can use either a two or three 

wire extension cord.
As the distance from the supply outlet 

2. 

increases, you must use a heavier 

gauge extension cord.  Using exten-

sion cords with inadequately sized 

wire causes a serious drop in voltage, 

resulting in loss of power and pos-

sible tool damage. 

(See Table A.)

  The smaller the 

gauge number of the wire, the greater 

the capacity of the cord.  For ex-

ample, a 14 gauge cord can carry a 

higher current than a 16 gauge cord.  

(See Table A.)

When using more than one exten-

3. 

sion cord to make up the total length, 

make sure each cord contains at 

This product

uses a

3-prong plug.

Summary of Contents for 98676




















Reviews: