background image

Page 19

SKU 98676

For technical questions, please call 1-800-444-3353.

record product’s Serial Number Here:

 

Note:

 If product has no serial number, record month and year of purchase instead.

Note:

 Some parts are listed and shown for illustration purposes only, and are not available individually as 

replacement parts.

LIMITED 1 YEAr / 90 DAY WArrANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and dura-

bility standards, and warrants to the original purchaser that for a period of ninety days from date of pur-

chase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects 

in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of 

one year from date of purchase, that all other parts and components of the product are free from defects 

in materials and workmanship (90 days if used by a professional contractor or if used as rental equip-

ment).  This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or 

accidents, repairs or alterations outside our facilities, normal wear and tear, or to lack of maintenance. We 

shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special 

or consequential damages arising from the use of our product. Some states do not allow the exclusion or 

limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to 

you.  THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IM-

PLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation 

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the mer-

chandise. If our inspection verifies the defect, we will either repair or replace the product at our election 

or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replace-

ment. We will return repaired products at our expense, but if we determine there is no defect, or that the 

defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning 

the product.

This warranty gives you specific legal rights and you may also have other rights which vary from 

state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

WIrINg DIAgrAM

L

N

pE

SWITcH

DIgITAL rEADOuT

SpINDLE SpEED SENSOr

MOTOr

Summary of Contents for 98676




















Reviews: