background image

Page 4

SKU 66305

for technical questions, please call 1-800-444-3353.

the specific tool model. 

Use of an 

accessory not intended for use with 

the specific tool model, increases the 

risk of injury to persons.

Service

Tool service must be performed 

a. 

only by qualified repair personnel.

When servicing a tool, use only 

b. 

identical replacement parts. use 

only authorized parts.
use only the lubricants supplied 

c. 

with the tool or specified by the 

manufacturer.

SyMboLS and Specific 

Safety inStructionS

Symbol Definitions

Symbol property or Statement

n

o

No-load speed

.../min

Revolutions or reciprocation per 

minute

pSi

Pounds per square inch of pressure

ft-lb

Foot-pounds of torque

bpM

Blows per minute

cfM

Cubic Feet per Minute flow

ScfM

Cubic Feet per Minute flow at 

standard conditions

npt

National pipe thread, tapered

npS

National pipe thread, straight

WARNING marking concerning Risk 

of Eye Injury.  Wear ANSI-approved 

eye protection.

chart continued in next column.

Symbol Definitions

WARNING marking concerning Risk 

of Hearing Loss.  Wear hearing 

protection.
WARNING marking concerning Risk 

of Respiratory Injury.  Wear NIOSH-

approved dust mask/respirator.

WARNING marking concerning Risk 

of Explosion.

Specific Safety Instructions

Strap Motorcycle to Lift before use.

1. 

The weight of the motorcycle must be 

2. 

centered directly over the Deck Plate 

(16) during use.
This lift is designed for standard 

3. 

two-wheel motorcycles only. Do not 

attempt to lift a motorcycle with side 

car or a three-wheeled vehicle.
Do not exceed the maximum 1000 lb. 

4. 

weight capacity of this tool. 

be aware 

of dynamic loading!

  Dropping or 

bouncing load may briefly create ex

-

cess load causing product failure.
Keep all fasteners and pull pins cor-

5. 

rectly installed and secure when the 

Lift is in use.
Always use the Safety Bar (75) as 

6. 

described in this manual when the 

Lift is raised. Never depend on the 

Hydraulic Ram (24) alone to keep Lift 

elevated.
Do not put Hands, arms, any body 

7. 

part or object within the interior frame 

of the Lift when raising or lowering.
Do not hold onto the Lift as it is raised 

8. 

or lowered.

Summary of Contents for 66305

















Reviews: