Center 265 Operating Manual Download Page 13

Page: 13 / 13

Clamp Meter

8. MAINTENANCE

WARNING!

Before opening the meter, disconnect both test leads. Never use the

meter unless the battery cover is in place and the screw is tightened.

CAUTION!

To avoid contamination or static damage, do not touch the circuit

board without proper static protection.

8-1 REMARKS:



If the meter is not going to be used for a long time then please

remove the battery and do not store the meter in a high temperature

or high humidity environment.



Keep the cable in the center of the clamp will return a more accurate

test result when making current measurements.



Repairs or servicing not covered in this manual should only be

performed by qualified personnel.

8-2 CLEANING:

Periodically wipe the case with a dry cloth. Do not use abrasives or

solvents on these instruments.

Distributed By :

TRIO Test & Measurement Pty Ltd

T. 1300 853 407
F. 1300 853 409

[email protected]

http://www.triotest.com.au

Summary of Contents for 265














Search results

Summary of Contents for 265

Reviews:

Related manuals for 265

Brands by name

Popular brands

Center 265, Operating Manual

Search results

Summary of Contents for 265

Reviews:

Related manuals for 265

Brands by name

Popular brands