CenRF CEW-P10 User Manual Download Page 18 | Manualshive

Page: 18 / 24

background image

Page 18 of 24

8.4.2. Repeater’s ports description

1)

Outdoor port: connected with the donor antenna by cable

2)

Indoor port: connected with server antenna directly or by cable

3)

DC IN: connected with power supply.

8.4.3. Accessories selection

Please pay attention to the two points of “frequency” and “impedance” during the selection of the accessories.

All accessories shall support the repeater’s frequencies from feeder line, antenna and splitter to combiners etc.

For example, the repeater’s frequency is WCDMA, so all the accessories must support the WCDMA

1920-2170MHz frequency. And the repeater’s impedance is 50ohm, so the accessories shall all be 50ohm. To

use any other impedance of coax will put an extra load on your repeater, shorten its life span and decrease the

system performance.

8.5. Repeater Settings

Please check very carefully all cable connections are correct and firm before running operation test and then

carry out following tests

8.5.1. Switch on power

After power is on, check firstly the alarm and power LED’s.



Status and definition of POWER indicators:

«
...
16
17
18
19
20
...
»

Summary of Contents for CEW-P10

























Reviews:

No comments

Related manuals for CEW-P10

Brand: VEAB Pages: 24

Brand: nedis Pages: 7

Brand: Parmet Pages: 6

Brand: LINK-MI Pages: 3

Brand: FACTO Pages: 21

Brand: ElectrIQ Pages: 24

Brand: Dru Pages: 56

Repeater RP 6004

Brand: DIS Pages: 14

Brand: Haverland Pages: 16

Brand: Aurora Pages: 5

Brand: emerio Pages: 86

Brand: YOKOGAWA Pages: 4

Brand: CSI Pages: 36

Therma Grow 120

Brand: L.B. White Pages: 8

CANOPIA GP 08 24

Brand: Palram Pages: 22

Brand: Jata Pages: 32

DUAL-KHER DK1000P

Brand: Jata calor Pages: 20

Brand: Draper Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands