17
5. INSTRUCTIONS FOR USE (Cutting operation)
STEP 1- Checking and testing the unit prior to cutting operations
Check all components (cutting head, flexible hose, couplings and pump) before use to verify there
is no damage or leakage.
Proceed as follow:
Check the battery charge and recharge it if necessary following the instructions in the battery
charger user manual.
When a cutting operation begins, a check is made from the electronic
card to determine whether the battery charge is sufficient to complete the cutting operation.
If this is not the case the pump does not start. The LED (4) light will FLASH intermittently
and the buzzer (5) will emit an audible signal coordinated with the LED light.
Remove the battery from the pump (Ref. to Fig. 5).
Connect the flexible hose first to the cutting head and then to the
pump
(Ref. to Fig. 6).
Insert the battery into the pump.
Activate the pump by pressing forward the control button (12) on
the pump, the display lights up and the pump setting is displayed.
Turn on the radio control by pressing the ON/OFF button (1), the LED will
flash green, after 3 minutes the radio control automatically switches off.
Press the pump button (2) on the radio control to perform a test cutting
operation.
During the operation the pump's LED light will FLASH
intermittently and the buzzer will emit an audible signal coordinated with the LED light.
At the end of the operation the pump will stop, the LED will remain a
STEADY LIGHT
(2 minutes)
and the speaker will emit a
COUNTINUOUS BUZZER
sound (30 seconds). This confirms the pump
received a signal from the cutting head acknowledging that the blades
are completely closed; the display will show the following flashing screen
(Ref. to
section 7.5
for further details).
Release the finger from the pump button (2) to initiate the SMART RELEASE function of the pump;
the operator should then check to ensure the blades are fully retracted to the start position.
Remove the battery from the pump.
Disconnect the flexible hose from the pump and cutting head.
Cutting operations must be strictly in accordance with the
safety and working procedures established by the respon-
sible power utility.
P
p
= 325 bar
RESET
SW:S1J41405
LED
OFF
ERROR
001
30001
BATTERY
P
n
= 729 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B68RC
17AW125
10
29990
BATTERY
max 90°
90°
OK
P
n
= 729 bar
P
p
= 731 bar
RC ON
RESET
SW:S1J76202
P
n
= 729 bar
P
= 0 bar
P = 0 bar
P
n
= 10573 psi
LED
ON
LED
OFF
max 90°
60°
*
1
*
2
3
4
5
*
6
*
7
*
8
*
9
10
P
= 0 psi
P = 0 bar
P
n
= 729 bar
P
= 0 bar
BEEP
BEEP
RC OFF
P
n
= 729 bar
OK
OK
SAVE 60
%
100
P = 0 psi
P = .... bar
NTC
FAULT
P
n
= 729 bar
OK
P
n
= 729 bar
P
p
= 731 bar
P
n
= 729 bar
P
= 0 bar
58
01
59
60
.........
P
p
= 325 bar
RESET
SW:S1J41405
LED
OFF
ERROR
001
30001
BATTERY
P
n
= 729 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B68RC
17AW125
10
29990
BATTERY
max 90°
90°
OK
P
n
= 729 bar
P
p
= 731 bar
RC ON
RESET
SW:S1J76202
P
n
= 729 bar
P
= 0 bar
P = 0 bar
P
n
= 10573 psi
LED
ON
LED
OFF
max 90°
60°
*
1
*
2
3
4
5
*
6
*
7
*
8
*
9
10
P
= 0 psi
P = 0 bar
P
n
= 729 bar
P
= 0 bar
BEEP
BEEP
RC OFF
P
n
= 729 bar
OK
OK
SAVE 60
%
100
P = 0 psi
P = .... bar
NTC
FAULT
P
n
= 729 bar
OK
P
n
= 729 bar
P
p
= 731 bar
P
n
= 729 bar
P
= 0 bar
58
01
59
60
.........
12
TG.0932
TG.0932
TG.1139
