CEMARLINE MAXX-700 User & Installation Manual Download Page 4

 

 

Page 4

 

 

 

 

CAUTION 

- Indicates a potentially hazardous situation which, if not avoided, may result in minor 

or moderate injury. It may also be used to alert against unsafe practices. This signal word is to be 
limited to the least dangerous situations. 
 

1.2.1  Laser Safety

 

 

 

 

WARNING 

There is a risk of an incorrect diagnosis or treatment.

 The isocenter of the lasers 

must coincide with the isocenter of the diagnostic or treatment equipment. Testing the alignment of  the 
lasers to the isocenter of the diagnostic or treatment equipment is based on the hospitals procedures. Newly 
installed equipment can possibly shift as building walls and floors settle and as building materials dry out. 
If the equipment or the lasers have been moved, it is advised to realign the  lasers to the isocenter before 
use. 

 

 

CAUTION 

The laser light is a risk for eye damage.

 The laser used in the MAXX-700 patient 

positioning system is a Class 2 laser. To prevent eye damage, do not allow patients to stare into the laser 
beam. The normal blink reflex will prevent eye damage. If a patient is unable to blink normally, then the 
laser operator must prevent the laser from shining into the patient's eye. 

 

1.2.2  Safety Labels 

 

 

 

Three safety labels are placed on each MAXX-700 laser unit in the locations shown below: 

 

 

 

 

1. At the upper left corner 

on the left side of the 

cover. 

2. Right under the 

window on the front side 

of the cover. 

3. At the upper right 

corner on the right side of 

the cover. 

Summary of Contents for MAXX-700




















Reviews: