background image

Issue 4.0 

CEECO 

Communication Equipment & Engineering Company 

PROPRIETARY 

12

 

11.0  REPAIR AND RETURN INFORMATION 

 
 
 
 

11.1

   WARRANTY REPAIR 

 

Any device returned requiring warranty service, repair or credit must be 
accompanied with a "Return Material Authorization" (RMA) FORM.  It 
must include return shipping instructions, original purchase order number 
and special marking instruction.  A description of the trouble observed 
must be attached to the defective unit.  This information must be inside the 
shipping container. 

 
 

11.2

   DIRECT ALL INQUIRES TO:

 

 
 

CEECO 

Repair Department 

863-357-0798- telephone 

863-357-0006- facsimile 

[email protected]

 

www.ceeco.net

 

 
 

11.3  

NON-WARRANTY REPAIR 

 

CEECO will repair equipment out of warranty for a set charge plus parts.  
The customer must pay the shipping costs both directions. 

 
 

11.4

   RETURN FOR CREDIT 

 

Material may be returned for credit only with prior approval. Material 
authorized for return is subject to a 20% restocking charge based on the 
manufacturer’s list price.  Return RMA must be requested no later than 30 
days after original shipment. 

 

 

Summary of Contents for SSP-561-D















Reviews: