Cedima CTS-125 G Operating Manual And Safety Instructions Download Page 9

Page: 9 / 54

ENGLISH

•

CEDIMA

1-1

Technical data and accessories

1.0 Technical speciﬁcations of the bench saw CTS-125 G

Output and

electrical ratings of the drive motor

Electric protection

SOLIDMAN: 2,2 kW (2800 rpm)

230 V at 50 Hz, 10 Amp.

EMG: 2,2 kW (2770 rpm)

230 V at 50 Hz, 12 Amp.

IP 55

Saw blade diameter maximum

Saw blade diameter minimum

Max. cutting depth

Max. cutting length

Saw blade receptacle Ø

Speed (rpm) of the blade shaft (rated speed)

400 mm

300 mm

125 mm

510 mm (at a cutting depth of 10 mm)

25,4 mm

SOLIDMAN: 2800 min

-1

, EMG: 2770 min

-1

Dimensions

Length

Width

Height

Weight

Weight inclusive water

1145 mm

580 mm (700 mm inclusive measured support legs)

605 mm (transport), 1345 mm (ready to work)

76,5 kg

approx. 111,5 kg

Water supply

Output of water pump

Water capacity

approx. 11,6 l/min

approx. 35 l

Water is led to the diamond saw blade through the water distributor at the saw blade guard

Electric fuse protection within the electrical

distributor (mains supply)

essential protection

preferable protection

L 16 Ampere

G 16 Ampere

1.1

Sound ranging (as per DIN EN 31201, EN ISO 3744, 20007 14/EG)

CTS- 125 G

Sound pressure level at place of work (Lpa)

81,1 dB(A)

Sound power level (Lwa)

94,3 dB(A)

Sound ranging made with static machine, at rated speed, with saw blade (Ø 400 mm).

During cutting operation higher sound levels are possible to occur!

Summary of Contents for CTS-125 G



















































Search results

Summary of Contents for CTS-125 G

Reviews:

Cedima CTS-125 G, Operating Manual And Safety Instructions, Page: 9 / 54

Search results

Summary of Contents for CTS-125 G

Reviews: