Cedes TOF/Start-EA Installation And Operation Manual Download Page 3

TOF/Start-EA

English

© CEDES | V 1.0

 

3

2.  Safety information

The TOF/Start-EA was developed and manufactured using 
state-of-the-art systems and technologies. However, injury 
and damage to the sensor can still occur.

To ensure safe conditions:

 

Read all enclosed instructions and information.

 

Follow the instructions given in this manual carefully.

 

Observe all warnings included in the documentation 
and attached to the sensor.

 

Do not use the sensor if it is damaged in any way.

 

Keep the instruction manual on site.

The TOF/Start-EA should only be installed by authorized 
and fully trained personnel! The installer or system 
integrator is fully responsible for the safe integration 
of the sensor. It is the sole responsibility of the planner 
and/or installer and/or buyer to ensure that this product 
is used according to all applicable standards, laws and 
regulations in order to ensure safe operation of the whole 
application.

Any alterations to the device by the buyer, installer or user 
may result in unsafe operating conditions. CEDES is not 
responsible for any liability or warranty claim that results 
from such manipulation.

Failure to follow instructions given in this manual and/or 
other documents related to the TOF/Start-EA may cause 
customer complaints, serious call backs, damage, injury 
or death.

2.1  Non-intended use

The TOF/Start-EA 

must not

 be used for:

•  Protection of dangerous machines
•  Equipment in explosive atmospheres
•  Equipment in radioactive environments

Use only specific and approved safety devices for such 
applications, otherwise serious injury or death or damage 
to property may occur!

3.  Symbols, safety messages

3.1  Safety messages categories

Warning of serious health risks

Caution of possible health risk

Notice of damage risk

Symbol

Meaning

 

 

Single instruction or measures in no 
particular order

1.   
2.   
3.   

Sequenced instructions

•   

List, in no order of importance

à

Reference to a chapter, illustration or 
table within this document

Important

Important information for the correct use 
of the sensor

WARNING

Serious health risks

Highlights critical information for the safe 
use of the sensor. Disregarding these 
warnings can result in serious injury or 
death.

 

Follow the measures highlighted by the 
triangle-shaped arrows

 

Consult the safety information in 
Chapter 2 of this manual

IMPORTANT

READ BEFORE INSTALLATION!

CAUTION

Possible health risks

Highlights critical information for the safe 
use of the sensor. Disregarding these 
warnings can result in injury.

 

Follow the measures highlighted by the 
triangle-shaped arrows

 

Consult the safety information in 
Chapter 2 of this manual

NOTICE

Risk of damage

Disregarding these notices can lead to 
damage to the sensor, the door controller 
and/or other devices.

 

Follow the measures highlighted by the 
triangle-shaped arrows

Summary of Contents for TOF/Start-EA













Reviews: