Cedar Summit BROOKRIDGE PLAY SYSTEM Installation And Operating Instructions Manual Download Page 17

Page: 17 / 56

[email protected]

Step 3: Swing Beam Assembly

Make sure triangle is

tight against beam

Warning: For your child’s safety,

orientate the swing hangers as

shown to ensure your swing will

have proper swing motion when

installed. Failure to do so could

result in premature failure of the

swing hanger or swing chain.

In the middle holes of (1825) Back

Beam install 2 Bolt-Thru Swing Hangers

(fig. 3.1) making sure the swing hangers

are oriented in the direction shown in fig.

3.4 to maintain proper swing motion.

In the end holes of (1826) Front Beam install 2

Bolt-Thru Swing Hangers (fig. 3.1) making sure the

swing hangers are oriented in the direction shown in

fig. 3.4 to maintain proper swing motion.

4 x

1/4 x 5-1/2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

5/16 x 1-1/2” Hex Bolt

(5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

1 x Bolt-Thru Swing Hangers (pkg of 4)
1 x Triangle Plate (pkg of 4)

1 x

Front Beam 2 x 6 x 83-5/8”

1 x

Back Beam 2 x 6 x 83-5/8”

1826

1825

Fig. 3.4

Bolt-Thru Swing Hangers

Wood Parts

Hardware

Other Parts

Fig. 3.1

Attach 1 Triangle Plate to the

ends of each (1826) Front Beam

and (1825) Back Beam using 1

(G1) 5/16 x 1-1/2” Hex Bolt (with

lock washer, flat washer and t-nut)

in the hole indicated in fig. 3.2 &

3.3.

Correct hole usage is very

important.

Triangle

Plates

Important!

Swing End

(With Overhang)

1826

Important!

Fort End Side

(No Overhang)

Fig. 3.2

Fig. 3.3

Attach 1 (H7) 1/4 x 5-1/2” Hex

Bolt (with lock washer, flat washer

and t-nut) to the ends of each (1826)

Front Beam and (1825) Back Beam.

The bolts do not attach to anything,

but

MUST

be installed to the beams

to prevent splitting and checking of

wood. (fig. 3.2 & 3.3)

Swing End

(With Overhang)

Fort End Side

(No Overhang)

1825

1/4” Flat

Washer
1/4” Lock

Washer

1/4” T-Nut

5/16” Flat

Washer

5/16” Lock

Washer

5/16” T-Nut

1826

1825

Bolt-Thru Swing Hangers

Make sure holes are aligned.

Summary of Contents for BROOKRIDGE PLAY SYSTEM

























































Search results

Summary of Contents for BROOKRIDGE PLAY SYSTEM

Reviews:

Related manuals for BROOKRIDGE PLAY SYSTEM

Brands by name

Popular brands

Cedar Summit BROOKRIDGE PLAY SYSTEM, Installation And Operating Instructions Manual

Search results

Summary of Contents for BROOKRIDGE PLAY SYSTEM

Reviews:

Related manuals for BROOKRIDGE PLAY SYSTEM

Brands by name

Popular brands