cecotec 05554, Instruction Manual, Page: 24 / 33

4 7 4 6
ENGLISH ENGLISH
The following modes and operations can be activated from the remote control.
Modes
The first time the robot is operated, it will map and save the whole house’s map by means of
its laser before starting the cleaning cycle. Use the robot in Auto mode and Eco power level,
this way you will ensure the robot memorizes the full map.
Note: Make sure the light indicator is lighted in blue before starting cleaning, indicating it is
activated. If not, press any button on the remote control to wake it up.
Auto mode
Fig.17.
(Рage 60)
Press the power button on the remote control for it to start cleaning automatically, first
a cleaning cycle in Edge mode and then another cycle in and organized zigzag motion,
recognizing which areas it has cleaned and which ones it has not. The robot will
automatically plan the cleaning route as it is cleaning. If during this mode the robot is
controlled manually, the robot will calculate the route again and could go through previously
cleaned areas. In order to ensure efficient cleaning, do not operate it manually during auto
mode cleaning.
Thanks to its Total Surface 3.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it
will resume the cleaning process from the same point, offering a high-efficiency cleaning.
During cleaning, the robot will stop briefly to evaluate the area and calculate the cleaning
route (this stop will vary depending on the house conditions).
Note: The robot cleans in an organized way and per 4x4 m squared areas, therefore it might
leave the room where it is cleaning to finish off the delimited area. Do not worry, the robot
will clean all the accessible surface.
Edge mode
Fig.18.
(Рage 60)
Press the Edge mode button on the remote control for the robot to start cleaning under this
mode. It will automatically start cleaning along all the surface’s perimeters and then will
return to the charging base direct and automatically. If the robot has not started cleaning
from the charging base, it will return to the starting point.
Note: Press the power levels button to switch between the 3 modes: Turbo/Normal/Eco.
Back home mode
Fig.19.
(Рage 60)
Press the Back-home button on the remote control in order to send the robot to the charging
base. This function can be activated during any other cleaning cycle and the robot will
automatically return to the charging base and stop the cleaning process. The robot will take
the shortest route back to the charging base thanks to its map memorizing and the smart
back home function.
When a cleaning cycle has been completed or the robot’s battery is low, thanks to its Total
Surface 3.0 technology, the robot will also return to the charging base to avoid running out of
battery. Once the robot has recharged, it will resume cleaning from the point it has stopped.
Warnings:
Remove the Wet & dry tank from the robot before charging it.
Make sure there are no obstacles in the room being cleaned to ensure the robot can get to
the charging base without problems.
Functions
Pause
While the robot is operating, press the power button on the App, the remote control or on the
robot to pause it and press the same button again to resume cleaning.
Standby
The robot will automatically enter standby mode after 5 minutes of no operation.
Press the power button on the App, the remote control or on the robot to start it up again.
Warnings:
After 12 hours of no operation, the robot will turn automatically off.
The robot will not enter standby mode during charging.
Suction power level
Press the power levels button on the remote control to select the desired power level.
Choose between Eco (low power), Medium (medium power) and Turbo (high power).
Schedule
Warning: The robot cannot be scheduled from more than one device at a time. Make sure to
schedule it either from the mobile phone App or from the remote control.
The robot is provided with a schedule function in order to provide a maximum-efficiency
cleaning. The time settings and the cleaning scheduling must be carried out from the remote
control. Once the robot has been scheduled, it will automatically carry out the cleaning cycles
every scheduled day.
Note: Make sure the robot is activated and that the light indicator is lighted before scheduling
any cleaning or setting time.
Current time
Fig.20.
(Рage 61)
Hold down the time button for 3 seconds. The first 2 digits, indicating the hour, will start
blinking.