background image

 
GRIDDLE NOT HEATING PROPERLY: 

 

Problem 1

:         Griddle does not heat when thermostat knob(s) is turned ON. 

                         

Pilot light(s) do not light. 

 

Possible Cause

:   Loss of power to griddle. 

 

REMEDY:

   

Check line fuses or circuit breakers at power source. 

 

Problem 2:

   

Only part of griddle plate works properly and the thermostat pilot does not light on faulty 

                             part of Griddle. 

 
Causes:                

A. Thermostat set too high or too low needs adjusting. 

                              B.  Faulty thermostat which must be replaced. 
 

REMEDY:

          A. Follow Adjustment procedure in “THERMOSTAT ADJUSTMENT” paragraph above. 

                             B. Replace thermostat as follows: 
 

CAUTION:  DISCONNECT POWER FROM GRIDDLE BEFORE ATTEMPTING ELECTRICAL 

REPAIRS 

 

1.

 

Tilt griddle on its side.  

2.

 

Remove front panel (4 mounting screws on the front, 2 on bottom).  

3.

 

Remove bottom cover (6 mounting screws). Take care not to damage the line cord. 

4.

 

Disconnect wires from heating element.  

5.

 

Disconnect thermostat bulb from plate by removing the two screws holding capillary clamp.  

6.

 

Remove thermostat knob.  

7.

 

Remove the two screws holding thermostat in place. Lift out thermostat and disconnect the wires, tagging 
them to be certain they are replaced on the proper terminals of the new thermostat.  

8.

 

Install new thermostat by following the above procedure in reverse order.  

9.

 

Calibrate thermostat, following the procedure in “THERMOSTAT ADJUSTMENT” paragraph above.  

 

Problem 3:

  Thermostat(s) works properly, but there is insufficient heat in one or more zones of griddle. 

 

Possible Cause:  

Heating element(s) burned out on zone(s) of plate not operating properly. 

 

REMEDY

:  Replace heating element(s) as follows: 

1.

 

Perform steps 1 through 5 of “Replace Thermostat” procedure above. 

2.

 

Remove heating element retainer plate. 

3.

 

Install new heating element by following the procedure above in reverse order. 

 
 
NOTE: 
DO NOT OVERTIGHTEN SCREWS HOLDING HEATING ELEMENT RETAINER PLATE IN PLACE. 
 

 
 

A circuit diagram has been provided to assist qualified technicians. A Recommended 
Qualified Service Technician should carry out repairs if needed. Do not remove any 
components or service panels on this product. 

 
 
 
 

Summary of Contents for HDECG2424







Reviews: