CEBEK CD-34 Quick Start Manual Download Page 4

4

HOW TO REMOVE THE BATTERY.

REMOVE AND SUGGESTIONS REGARDING BATTERY.

 When the mdoule is not supplied, the module maintains 

timing thanks to the battery. The hour display is cancelled till the module is again normally supplied; then the 
hour and the rest of the others functions will be activated again. 
With the time and according to the number and duration of situations in which 
the module was not supplied, the battery will be discharged. In this case, the 
module could not recuperate the hour and you have to remove the battery. 
The required battery is a 3 V CR-2032 battery, and you could purchase it to your 
distributor. 
When you will substituate it, be careful in respecting the corresponding polarity. 
See the schedule. Do not remove the battery if the module’s power supply is 
connected, neither hardly handle it.

C

20

3

R

2

3 V

.

BA

TER

Y

Battery

All the module’s CEBEK have 

3 years of total warranty 

in thecnical 

repairing, and spares from the date of buy.

CEBEK is trade make of FADISEL S.L. more than 300 module’s are avaible in 
stock for any purpose 

request our CATALOGUE, 

or visit our Web.

 

Http://www.cebek.com

TECHNICAL CONSULTATIONS.

If you have any doubt, you could contact your wholesaler or our Technical  Department.
- Via E-Mail,  

[email protected]     |    

by mail

 

 P.O Box 23455  - 08080  BARCELONA - SPAIN.

Keep the invoice of this module

. For any repair, the corresponding invoice had to be added. If the invoice is 

not presented together with this module, the module’s warranty will be automatically cancelled. 

GENERAL WIRING MAP.

3

R2

0

2

C 3 

V.

BA

TE

RY

Batter y

JP1

Module

CD-34

Power Supply

230 V. AC. Mains

Mains

Switch

250 mA.

Fuse

Apparatus o Machine

to be controlled

 by the CD-34

Led

Module

FE-71

TRANSFORMER.

FE-71

0

0

12

230

COUNTERS

CD-34

CD-34

Ref. Full9813

CD-34

CD-34

OPERATING.

HOURS CONTROLLER.

3

JP1

Desold to show

stored registers.

Lateral View of the JP1 Jumper

converted on P1, P2 and P3 buttons.  
It is very important to take in account two basic aspects : Firstly module will record data from the present month, 
erasing them each new month. For this reason, if you have to note monthly data, you have to write them at the 
latest time the last day of the month. The second aspect is the accurate displayed data. Thanks to the calcul of 
time averages, etc... The module could display as amaximum an error of minutes. Each button is used to have 
access to different registers and thanks to the LD2 led, you could know which is the register : 

P3.

 Press the P3 button till the LD2 led will light on. On the display you could read the total number of the real 

hours that the mdoule had operated, independently if the module had been connected some instants each 
day or the quantity of days, this register add and show total hours and minutes concerning the connection 
apparatus from the beginning till the date. If you press again on the P3 button, the LD2 led will light on an 
intermitten mode, indicating thatthe displayed register correspond to the starting date (the last time that the Start 
button had been activated). If you press again, the display will show the third and last register for the P3 button. 
The LD2 led will light off and display show the register corresponding to the starting hour (the last time that the Start 
button had been activated). If youpress again on the P3 button, the module will display these three register on a 
cyclic mode. 

P2.

 The P2 button show 2 registers. If youpress a first time, the LD2 led will light on, indicating that the displayed 

register correspond to the total number of operating days for the controlled apparatus or device. Then, the 
module will add all days of the month, in which the apparatus had been connected, independently if the 
apparatus had been connected several hours or one minute during the day. If the apparatus has not been 
connected one day, this day is not taking in account. 
If you press again on the P2 button, the module willshow the last register. The LD2 led will intermittently light and 
the display will show the average of worked hours per day. If you press again several times on the P2 button, the 
module will display these two registers according to a cyclic mode.

HOW TO HAVE A FAST ACCESS TO CD-34’S REGISTERS.

Frontal del Módulo

Hours/Days

Minutes/Months

Seconds/Years

LD1

LD2

P1

P1

P2

P3

P2

P3

1st pulsation.

 LD2 light on.

Time for “ today ” corresponding to the apparatus’operating time.

2sd pulsation.

 LD2 intermittent. Time for “ this week” corresponding to the apparatus’operating 

1st pulsation.

 LD2 light on.

Number of days corresponding to the appartus’ connection.

2sd pulsation.

 LD2 intermittent. Hours average done per day.

1st pulsation.

 LD2 light on.

Number of Total operating Hours.

2sd pulsation.

 LD2 intermittent. Starting Date.

HOW TO CONNECT THE MODULE AND THE APPARATUS TO CONTROL.

 To allow the CD-34 to control a 

determinated apparatus, you have to install it in parallel. Then, supplying or not the apparatus , you could also 
supply or not the CD-34. See the schedule.

Y

S

E R

A

E L E C T R O N I C C I R C U I T S

 

Summary of Contents for CD-34

Page 1: ...s module specially designed to control yield could be used on restricted mode to avoid to modify data because of a wrong manipulation and or an accident For this reason the keyboard usually used to display data could be used to activate stop or reset the module s count only when you wish it Then the employe even if he uses the keyboard for other applications he could not have access to activation ...

Page 2: ...d confirming you that adjustment operation is stopped To leave this function you have to desold the JP1 jumper and press P3 button ACTIVATION STOP AND RESET If the JP1 jumper were disconnected connect it again Then P1 P2 and P3 buttons will be used to respectively control Activation Stop and Reset functions If you press the Start button the LD1 Led will light indicating that the timing of the circ...

Page 3: ...how the register corresponding to the starting hour the last time that the Start button had been activated If youpress again on the P3 button the module will display these three register on a cyclic mode P2 The P2 button show 2 registers If youpress a first time the LD2 led will light on indicating that the displayed register correspond to the total number of operating days for the controlled appa...

Page 4: ...ty in thecnical repairing and spares from the date of buy CEBEK is trade make of FADISEL S L more than 300 module s are avaible in stock for any purpose request our CATALOGUE or visit our Web Http www cebek com TECHNICAL CONSULTATIONS If you have any doubt you could contact your wholesaler or our Technical Department Via E Mail sat cebek com by mail P O Box 23455 08080 BARCELONA SPAIN Keep the inv...

Reviews: