background image

20

GB

12.

Never

pull the appliance by the cord to move it.

Never

unplug it by pulling the cord or touching

it with wet hands.

If the power cable is damaged it must be replaced by the manufacturer or by the

technical assistance service, or at any rate by a person with similar qualifications, so

as to prevent all risks.

13.

WARNING:

Never place any utensils, metal or other hard materials, in the bean hopper. This

is dangerous and could cause damage.

14.

Do not

use the appliance if it is damaged or has loose parts. Immediately contact an authorized

Service Center.

The appliance complies with European regulation CE 1935/2004.

Note: Due to statistical tests on the product in the factory, some coffee grounds may be found in the appliance.

SAVE THESE INSTRUCTIONS

!

INSTALLATION

Comply with the

safety recommendations

indicated above and hereafter when installing the

appliance.

For the installation of the appliance, qualified personnel must be present who are able to check the

fineness of the grind.

1. Make sure that the mains voltage is as indicated on the rating label of the appliance and that

the electrical system is grounded and equipped with a switch.

2. Install the appliance in a

DRY, PROTECTED place

, far from water sprays or splashes, heat

sources, open flames and inflammable substances.

Place the appliance on a

flat, horizontal, stable surface

where it cannot tip over.

3. Put the tray in its housing to keep the work area as clean as possible.

Before connecting the plug to the power socket, make sure that the ON-OFF switch

(16 Fig. 2) is in position “O” (OFF).

4. Plug the power cable into a socket protected by a suitably rated circuit breaker (MCB) or fuses.

Do not use an adaptor plug.

5. Stretch the power cable out to full length.

Do not

let it pass over sharp edges or hot surfaces.

Do not

let oil spill on it.

Do not

let the power cable hang loose from the counter on which the

appliance stands.

6. Make sure that the bean hopper is correctly positioned and that its shutter (5 Fig. 2) is

completely open (to the last click).

The EC declaration of conformity for this appliance is available in the

Products

section of our

website

www.ceado.com

.

Summary of Contents for E37 Series















Reviews: