manualshive.com logo in svg

CDA WC680, Installation, Use And Maintenance Manual

Share
Download
CDA WC680 Installation, Use And Maintenance Manual Download Page 26

26

Failure Codes and Troubleshooting

The programme indicators also serve as a diagnostic display to help in 
the event of a problem with the appliance.

Error Code

Error description

Advice

Alarm is active against water 

overflow

•   Turn off the dishwasher and disconnect the water 

supply

•  Contact CDA Customer Care

The waste water cannot be 

discharged

•  Drain hose is blocked
•  The filters of your machine might be blocked
•  Restart the dishwasher and cancel the programme
•  If the error continues, contact CDA Customer Care

Continual fill error

•  Contact CDA Customer Care
•  Close the tap

Inadequate water supply

•  Make sure the water tap is fully open
•   Close the water tap, separate the water inlet hose 

from the tap and clean the filter.

•  Restart the dishwasher.
•  If the error continues, contact CDA Customer Care

Faulty heater sensor

•  Contact CDA Customer Care

Overheating error 

(temperature in the machine 

is too high).

•  Contact CDA Customer Care

Heater error

•  Contact CDA Customer Care

Spray diverter position error

•  Contact CDA Customer Care

Faulty electronic card.

•  Contact CDA Customer Care

Summary of Contents for WC680





































Reviews:

No comments

Brands by name

Popular brands

Load more brands