CDA WC461 Manual For Installation, Use And Maintenance Download | Manualshive

Page: 14 / 20

background image

14

Failure Codes and Troubleshooting

The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance.

Error Code

Error description

Advice

F1

Alarm is active against water overflow

• Turn off the dishwasher and disconnect the water supply

• Contact CDA Customer Care

F2

The waste water in the machine

cannot be discharged.

• Drain hose is blocked

• The filters of your machine might be blocked

• Restart the dishwasher and cancel the programme

• If the error continues, contact CDA Customer Care

F3

Continual fill error.

• Contact CDA Customer Care

F5

Inadequate water supply.

• Make sure the water tap is fully open

• Close the water tap, separate the water inlet hose from the tap

and clean the filter.

• Restart the dishwasher.

• If the error continues, contact CDA Customer Care

F6

Faulty heater sensor.

• Contact CDA Customer Care

F7

Overheating error (temperature in the

machine is too high).

• Contact CDA Customer Care

F8

Heater error.

• Contact CDA Customer Care

F9

Spray diverter position error.

• Contact CDA Customer Care

FE

Faulty electronic card.

• Contact CDA Customer Care

«
...
12
13
14
15
16
...
»

Summary of Contents for WC461





















Reviews:

No comments

Related manuals for WC461

Brand: GE Pages: 2

Brand: GE Pages: 5

Brand: Majestic Appliances Pages: 20

Brand: Panasonic Pages: 21

Brand: Campomatic Pages: 16

Brand: Hotpoint Pages: 16

Brand: Heinner Pages: 85

Brand: Kuppersberg Pages: 148

Brand: Miele professional Pages: 140

Brand: Samsung Pages: 110

WW80H5440E Series

Brand: Samsung Pages: 88

Brand: Samsung Pages: 136

WW80H5400E Series

Brand: Samsung Pages: 88

Brand: Candy Pages: 136

Brand: Candy Pages: 164

Brand: Candy Pages: 41

Brand: Currys Essentials Pages: 36

Brand: GEAppliances Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands