background image

18

This cooktop can be built into a working surface 30 to 40 mm 
thick and 600 mm deep.
In order to install the ceramic hob into the kitchen fixture, a 
hole with the dimensions shown in figure 3 has to be made, 
keeping in consideration the following:
–  The  cooktop  shall  not  be  installed  directly  above  a 

dishwasher, fridge, freezer, washing machine or clothes dryer, 
as the humidity may damage the cooktop electronics.

–  If  the  cooktop  is  installed  above  an  oven,  the  oven  shall 

be  provided  with  cooling  fan.  The  two  appliances  should 
be  connected  to  the  electrical  supply  with  independent 
connections.

–  IMPORTANT  WARNING!  This  cooktop  requires 

adequate  supply  of  fresh,  cool  air  to  fully  function. 
The base of the cooktop must have direct unrestricted 
ventilation to the room where the cooktop is installed. 
Follow the requirements of figure 5.

–  The ceramic hob must be kept no less than 60 mm away from 

any side wall (see figure 4).

–  The rear wall must be at least 50 mm from the ceramic hob 

(see figure 3).

–  There must be a distance of at least 650 mm between the 

hob  and  any  wall  cupboard  or  extractor  hood  positioned 
immediately above (see fig. 4).

–  The coatings of the walls of the unit or appliances near 

the cooktop must be heat resistant.

–  Do  not  install  the  appliance  near  inflammable 

materials (eg. curtains).

500 mm

650 mm

450 mm

Fig. 4

60 mm minimum between the side 
of the cut-out and the side wall

7 mm

7 mm

min 30 mm

min 30 mm

70 mm

Fig. 5

Minimum clearances and

ventilation requirements

(cupboard or drawer space below)

Minimum clearances and

ventilation requirements

(oven installed below)

Oven with

cooling fan

Summary of Contents for HVN 32 Series

























Reviews: