CDA EVC4 Installation And Maintenance Manual Download Page 4

3

Care and Maintenance

IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE 
EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

Cleaning 
You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will 
scratch the surface and could erase the control panel markings.  

You can clean your extractor effectively by simply using a dilute solution of water 
and mild detergent and drying to a shine with a clean cloth.

Cleaning the grease filter   
The grease filter should be kept clean to minimise the risk of fire.

When button A flashes every two seconds , or at least once a month you should 
remove and clean the grease filter with hot soapy water. You can also wash the 
grease filter in a dishwasher, ensuring that you place it in an upright position to 
prevent damage from other items in the dishwasher. After rinsing and drying, 
replace the filter. After the grease filter has been replaced, the electronic memory 
must be reset by pressing button A for approximately five seconds, until it    
stops flashing.

To remove the grease filter follow the steps below:

1. Push the cover panel to open the base of the extractor, as shown in fig 2.
2. Pull open the handle on the grease filter as shown in fig. 3. It will release       
     at the handle side. Then lower the grease filter to remove it completely.

To replace the grease filter, repeat the steps in reverse.

Please note: 
Cleaning the grease filter in the dishwasher may lead to discolouration. This is 
normal and does not constitute a fault with the appliance.

Changing the charcoal filter (re-circulating only)
When button A flashes every half second, the charcoal filters must be replaced.  
After the charcoal filter has been replaced, the electronic memory must be reset 
by pressing button A for approximately five seconds, until it stops flashing.

To attach a new charcoal filter, first open the body of the extractor and remove the 
grease filter as shown in figure s 2 and 3. Then offer up the charcoal filter into the 
frame as shown in figure 4 until it locks into place. Repeat with the other charcoal 
filter, then close the body of the extractor..

Fig. 3

Fig. 4

Fig. 2

Summary of Contents for EVC4













Reviews: