CDA EVC4 Installation And Maintenance Manual Download Page 2

Important

The manufacturer cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. 
Please note that the manufacturer reserves the right to invalidate the guarantee supplied with this product following 
incorrect installation or misuse of the appliance or use in a commercial environment. 

This appliance is not designed to be used by people (including children) with reduced physical, sensorial or mental 
capacity, or who lack experience or knowledge about it, unless they have had supervision or instructions on how to use 
the appliance by someone who is responsible for their safety.

Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified 
personnel.

Appliance information:
Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a 
fault with your appliance and to register your appliance for guarantee purposes.

  Appliance Model

  Serial Number

CE Declarations of Conformity:
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Gas 
safety, Electrical safety (LVD) and Electromagnetic interference compatibility (EMC).
 
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC 
DIRECTIVE 2002/96/EC.

At the end of its working life, the product must be taken to a special local authority waste collection centre or to a 
dealer providing appliance recycling services.  Disposing of a household appliance separately avoids possible negative 
consequences for the environment and health. It also enables the constituent materials to be recovered, saving both 
energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked 
with a crossed-out wheeled dustbin.

Please note:

   Under no circumstances should the extractor be connected to any gas ventilation system, flue system or hot air    

 

ducting system.

   Do not vent the extractor into an attic or loft space.

   Only house the extractor in rooms with adequate ventilation. Remember that the extractor is powerful and  

 

 

whatever air is extracted needs to be replaced.

   Do not tile the extractor in. It should be removable for service or maintenance.

   Do not use silicone sealant to secure the hood to the wall.

   You must be able to isolate the extractor from the mains electrical supply after installation.

   Steam cleaners must not be used when cleaning this appliance.

   The performance of your extractor will vary depending on a number of factors. These include: type of extraction,  

 

length of ducting, room volume, ventilation available and cleanliness of the filters.

1

Summary of Contents for EVC4













Reviews: