background image

 

Information in this document is subject to change without notice. No part of this document may be 
reproduced or transmitted in any form or by any means, electronic or mechanical without the prior written 
permission of Continental Control Systems, LLC.

 

 
 
©2007 Continental Control Systems, LLC. All rights reserved. 
Printed in the United States of America. 
Document Number: WNP-UL-1.20 
Revision Date: March 5, 2007 
 
Continental Control Systems, LLC. 
3131 Indian Rd., Suite A 
Boulder, CO 80301 
(303) 444-7422 
FAX: (303) 444-2903 
E-mail: [email protected] 
Web: http://www.ccontrolsys.com 
 
 
 WattNode is a registered trademark of Continental Control Systems, LLC. 
 
 
 

FCC INFORMATION 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area can cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 
 
 

Summary of Contents for WattNode Pulse Output





















Reviews: