T e le S w it c h
H e a t e r
TeleSwitch
M2
TeleSwitch is a perfect remote controlled switching and reporting unit for
residence, summer house, office and workshop use.
With TeleSwitch you can switch electrical appliance on or off via the telephone, or
receive a message in the case of for example a break-in, unauthorized access,
machinery stop, etc.
..
Technical specification:
Connection to the public telephone network
2 channels, which can either be programmed to be outputs (control) or inputs (message
or alarm)
4-digit security code
Timer functions from 1 to 99 hours per output.
Pulse activation of outputs (to be specified when ordering)
Alarm via telephone. TeleSwitch rings to a pre-programmed telephone number.
Number of rings before responding. (1 to 9 rings before responding)
Operated by normal touch-tone or mobile telephone.
Remembers the last change or setting in the case of a power cut.
Connected to a 230V mains power supply (a 12V supply can be specified to order).
Grounded to provide additional protection against lightning.
The outputs can be loaded to 230/250V 10A
Manual operation available on the front panel, with channel status indication.
Installation and user instructions
General description
TeleSwitch
is a remote control unit operating via the telephone network, with 2 function
channels.
TeleSwitch
is connected by means of an existing telephone/fax to the telephone network.
Each of the function channels can be programmed as an output
(e.g. to switch on or off
an electric heater, outdoor lighting, etc.)
or as an input
(e.g. to report
low temperature in a summer house, generate an alarm in the case of a burglary, etc.)
Outputs:
If a function channel is programmed
as an output, you can via telephone
decide whether the output
(contact in the
TeleSwitch)
is to be closed or opened.
TeleSwitch
has a built-in timer function (1 to 99 hours), which makes it possible to
decide how long an output is to remain closed. The timer function can however be switched off.
Inputs:
If a function channel is programmed
as an input, you can via telephone
receive a message whether a connected
message/alarm contact is closed or
open.
(The contact can for example be a non-touch
door contact to report burglary, a water level monitor in a groundwater well, etc.)
If the input is activated
(message/alarm switch connection)
TeleSwitch
can call a predetermined
telephone number and provide a message or alarm tone.
It is also possible to call
TeleSwitch
and check whether an input is activated.
TeleSwitch
is connected to the public telephone network via a normal telephone jack
and can be controlled by a normal touch-tone phone or a mobile telephone.
To ensure that no unauthorized person can ring to a
TeleSwitch
and interfere with its control of
the inputs and outputs,
It is equipped with a four-digit security code that you can select yourself.
You can choose from two types of
TeleSwitch
.
Table model
M1
and wall-mounted
module
M2
M1
is easy to install and can be brought into use without the help of a tradesman.
M2
requires installation by an authorized electrician as the
TeleSwitch
has to installed
connected to a high voltage distribution panel.
Both types need to be connected to a 230V mains power source.
The output contacts can have a maximum loading of 230 V 16A or 250 V 10A.
1
T e le S w it c h
D o o r c o n t a c t
Leveret af:
CB Svendsen A/S,
Kirke Værløsevej 22, 3500 Værløse
E-mail.
www.cb-svendsen.dk
Tlf. 44485286
– Fax. 44485784 – rev.: 06.07.2008
Telephone
network
Telephone,
mobile
(Worldwide)
Telephone,
land line
(Worldwide
)
Heat on /off
Telephone
230V
Net
”Door Surveillance”
Summer house, residence, office,
workshop etc.
