background image

Important

Note

Warning

 • Pay attention to the road or trail! Do not be distracted by the

computer.

 • Be sure to securely mount the magnet, the sensor, and the

bracket on your bicycle.  Periodically check to insure they are
mounted securely and the screws are not loosen.

 • Keep batteries out of reach of small children.  Dispose of batter-

ies according to local regulations.

 • Avoid unnecessary prolonged exposure to the sun.  Never at-

tempt to disassemble the computer head.

 • Don’t use thinner, benzene or alcohol to wipe the surface of the

computer. They may damage the surface of computer.

Computer Set-up

 (For 1st use or after replacing the battery)

All Clear

Push three buttons (MODE, START/
STOP and SET) at the same time.
* Do this procedure without fail for

stable measurement when you use
this system for the first time and every
time the battery is replaced.

1

Starting the odom-
eter from zero.

Retaining the current odometer reading

(the odometer starts from the reading you
inputted)

SET

MODE

MODE

ST/STOP

ST/STOP

Set The Tire Circumference

Set the tire circumference in cm.

Note

 You can easily set it by referring to the chart shown

right.

Setting is completed by pushing the SET button.

3

Increase the
number.
Max. 300 cm

Decrease
the number
Min. 100 cm

Preparation Complete.

 (the screen will show the time measurement in this state)

* The auto mode is ON in this state.

MODE Button

START/STOP Button

SET Button

!

L(cm)

14 x 1.50

102

14 x 1.75

106

16 x 1.50

119

16 x 1.75

120

18 x 1.50

134

18 x 1.75

135

20 x 1.75

152

20 x 1-3/8

162

22 x 1-3/8

177

22 x 1-1/2

179

24 x 1

175

24 x 3/4Tubular

178

24 x 1-1/8

179

24 x 1-1/4

191

24 x 1.75

189

24 x 2.00

192

24 x 2.125

196

26 x 7/8

192

26 x 1(59)

191

26 x 1(65)

195

26 x 1.25

195

26 x 1-1/8

190

26 x 1-3/8

207

26 x 1-1/2

210

26 x 1.40

200

26 x 1.50

201

26 x 1.75

202

26 x 1.95

205

26 x 2.00

206

26 x 2.10

207

26 x 2.125

207

26 x 2.35

208

26 x 3.00

217

27 x 1

215

27 x 1-1/8

216

27 x 1-1/4

216

27 x 1-3/8

217

650 x 35A

209

650 x 38A

212

650 x 38B

211

700 x 18C

207

700 x 19C

208

700 x 20C

209

700 x 23C

210

700 x 25C

211

700 x 28C

214

700 x 30C

217

700 x 32C

216

700C Tubular

213

700 x 35C

217

700 x 38C

218

700 x 40C

220

L cm

SET

ST/STOP

MODE

Contact Point

Select The Measurement Unit

Select the measurement unit, kilometer
or mile, by pushing the MODE button.

2

MODE

Choose Either of The Followings.
• When you want to input the reading of the currently

used odometer, keep pressing the MODE button for
two seconds and input the reading.

• When you want to start the odometer from zero,

push the START/STOP button.

Kilometer

Mile

SET Button

MODE Button

START/STOP
Button

Input the current reading of odometer.

For two seconds.

Increase the
number.

Move the
decimal point.

You need to know the tire
circumference (L cm) be-
forehand.

Tire size

Tire size is usually shown
on the sidewall of tires.

®

3

2
1

Installation of the Computer on Your Bike

The computer is combined with the following parts.

1

2

5

3

6

7

4

3

7

Important Note

Mount the sensor 

3

 at the appropri-

ate position so that the center of the
magnet 

5

  will align with the

marked line on the sensor when the
wheel is rotated.

Important Note

Rotate the sensor on the front fork to
adjust the gap between the sensor
and the magnet 

5

 within 5 mm, and

secure it with the nylon ties.

Mount The Bracket

Secure the cord on the front fork with the nylon ties (smaller ones) 

7

 and coil it around the

brake cable that leads to the handle bar.
Put the rubber pad 

6

 on the bracket 

1

 and secure the bracket on the handle bar with the

screw. Slide the computer into the bracket until you hear the click sound
The contact points are automatically closed. When you need to remove the computer, slide
forward the computer with the lever pushed simultaneously.

Note

  Allow enough wire clearance in the area marked with an

 to insure that you can

turn the handlebar from left to right without pulling the wire.

Basic Functions Test

Rotate the front wheel gently and see if the computer indicates the
running speed.

Note

  When the computer does not indicate the speed, check

the position of the magnet and the sensor.

4

3

5

1

 Bracket

2

 Cord

3

 Sensor

4

 Sensor Rubber Pad

Center

5

Magnet

6

Bracket Rubber Pad

7

Nylon Ties  (5)

Front Fork

3

2

1

Please read these instructions carefully before attempting to
install and use your CAT EYE MITY 8 computer so that you
understand the functions of this product.

Please don’t throw away this manual, Keep the manual at a place easily accessible.

5

Spoke

Rotate the front wheel.

OK

7

Front Fork

Sensor Side

Within 5 mm

Marked Line

1

Slide

1

6

Mount sensor and adjust the gap between the
magnet and the sensor.

Secure the sensor 

3

 with the larger nylon ties 

7

 at

the appropriate place and in the right direction.

Mount the magnet

5

 on a spoke of the front wheel so that the surface

of the magnet will face the sensor.

Lever

MITY8

CAT EYE  MITY 8

CYCLOCOMPUTER CC-MT400

E: Owner’s Manual

U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending

Copyright © 2002 CAT EYE Co. Ltd.

CCMMT4-021210  066600230  

1

You can refer to the guide
chart to roughly know the
tire circumference.

Summary of Contents for MITY 8 CC-MT400









Reviews: