manualshive.com logo in svg

CAT Pumps 3CP Series, Service Manual, Page: 6 / 20

Share
Download
CAT Pumps 3CP Series Service Manual Download Page 6

SERVICE MANUAL | 3CP Series Plunger Pumps

6

(763) 780-5440 | [email protected] | www.catpumps.com

Seal & Valve Kits 

SERVICE INTERVALS 

Typically, plunger pumps require only a very basic standard maintenance procedure of regular oil changes and seal and valve replacement.  
Seal and valve life are extremely dependent upon the type of pumped liquid, temperature, inlet conditions, system  protective devices, filtration, 
duty-cycle and maintenance-cycle. Most system failures are not due to the pump, but fail because of other system components.

The Preventative Maintenance Check-List (on page 18) provides a summary of the various system maintenance concerns for all high-pressure systems.

The seals on our pumps, operating under normal conditions, will perform for a minimum of 1500 hours, with most lasting much longer.  
The valves typically perform for 3000 hours, with many lasting much longer. Cat Pumps always recommends replacing these items as a kit  
since components usually wear at about the same rate.

Standard NBR kits shown below. See Data Sheet 993101 for alternative seal options.

SEAL KIT 

PN 33983  |  Qty 1

VALVE KITS

PN 33062  |  Qty 2

Summary of Contents for 3CP Series





















Reviews:

No comments