CASTLE GA112 Manual Download Page 21 | Manualshive

Page: 21 / 24

background image

Display Parameters

Sound Pressure Level either ‘A’ or Linear weighted with or without
Octave Band Filters. Battery condition indication.

Filters

Built in Octave Band Filters       to BS EN 61260 : 1996
Filter centre frequencies            31.5Hz, 63Hz, 125Hz, 250Hz,
                               500Hz, 1kHz, 2kHz, 4kHz,
                               8kHz, 16kHz.
Switch selectable                  OFF/MANUAL/AUTO.

Overload

Positive overload condition shown when Crest Factor is exceeded
(see also description on page 11).

Output Socket
AC Output:

120mV rms for FSD.

         Output impedance approx 600ohm.
                          Load impedance 10kohm or more.
                          Short circuit protected.

DC Output:

1.5V for FSD.

                          Output impedance approx 600ohm.
                          Load impedance 10kohm or more.
                          Short circuit protected.

Connector:

Lemo FGG0B303CLAD52Z

Microphone/Preamp

Pre-polarized ½” (12.7mm) Condenser Microphone
Sensitivity                       12mV/Pa
Capacitance                      15pF
Preamp output impedance           550R

21

«
...
19
20
21
22
23
...
»

Summary of Contents for GA112

























Reviews:

No comments

Related manuals for GA112

Brand: LaMotte Pages: 2

Brand: B meters Pages: 2

Brand: Vanguard Instruments Pages: 24

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hammond Pages: 16

Brand: Unico Pages: 96

Brand: M-system Pages: 18

Brand: QUBINO Pages: 2

Disklavier Mark III Series

Brand: Yamaha Pages: 39

Brand: GARANT Pages: 368

Brand: Magnescale Pages: 64

SourceMeter 2430

Brand: Keithley Pages: 141

Brand: Lutron Electronics Pages: 13

Brand: Dewetron Pages: 24

Brand: Oldham Pages: 96

Brand: Trotec Pages: 14

Brand: Power Measurement Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands