background image

 

Page 4 

Product Recycling and Disposal

 

 
 

European Union - Disposal Information for Commercial Users  
 

 

 

 

 

 
 
Application of this symbol on your equipment is confirmation that you must dispose of this 
equipment in compliance with agreed national Procedures. 
 
In accordance with European legislation end of life electrical and electronic equipment subject 
to disposal must be managed within agreed procedures. 
 
Prior to disposal please contact your local dealer for end of life take back information. 
 
 
 
European Union - Disposal Information for Domestic Users 
 

 

 

 

 

 
 
Application of this symbol on your equipment is confirmation that you should not dispose of 
the equipment in the normal household waste stream. 
 
In accordance with European legislation, end of life electrical and electronic equipment subject 
to disposal must be segregated from household waste. 
 
Private households within EU Member States may return used electrical and electronic 
equipment to designated collection facilities free of charge. Please contact your local disposal 
authority for information.  
 
In some Member States when you purchase new equipment your local retailer may be required 
to take back your old equipment free of charge. Please ask your retailer for information. 
 
 
 
Countries not within the European Union 
 
Please contact your local waste authorities and request disposal information. 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for Maxit 305













Reviews: