1
2
3
2
3
3
B
The answering machine is shipped with the Ring
Select Switch set to 4 rings. Set the
RING
SELECT SWITCH
(labeled RINGS) to 4, 2, or TS
(Tollsaver) to select the number of rings before
the TC-919 answers.
4 = The TC-919 will answer on the fourth ring.
2 = The TC-919 will answer on the second ring.
TS = When calling to retrieve messages from a
remote location, Tollsaver will help
eliminate toll charges by letting you know
if there are any new messages before the
TC-919 answers. When set to TS, the
TC-919 answers on:
Second ring = NEW messages
Fourth ring = NO new messages
Hang up after three rings to avoid toll
charges.
NOTE:
■
After you have retrieved messages, (from a remote
location or at the machine) Tollsaver will reset to
answer on the fourth ring until a new message is
recorded.
1
1
You can record one or two customized greetings
up to 20 minutes in length. The greeting is
recorded on a digital chip.
NOTE:
■
The sound level is automatically adjusted when the
greeting is played over the phone line.
3
4
BASE MESSAGE PLAYBACK
1
Press
GREETING RECORD
again after
you have finished speaking. The greeting
replays automatically and the TC-919
resets to answer phone calls with Greeting
One.
RECORD GREETING TWO
To record Greeting Two, press
GREETING SELECT
to set the TC-919
to answer with Greeting 2, then follow the
steps noted above in the section "RECORD
GREETING ONE."
You can listen to either greeting anytime when
the TC-919 is turned on.
1
Press
TIME SET
(located in the cradle ).
Press
TIME SET
again after hearing
"
Sunday, 12:00 a.m.
" You will hear,
"Sunday."
Set the current time and day. The TC-919 will
stamp each message with the time and day.
Press
TIME SET
again. The TC-919 will
announce the hour.
4
Press
SKIP/+
to advance or
REPEAT/-
to reverse the hour. “a.m.” and “p.m.” will
be announced for each hour.
1
Press
ON/OFF
(located in the cradle ) to
turn the answering machine on and off.
The PLAY/PAUSE INDICATOR on the base
will light when the TC-919 answering
machine is on.
ON/OFF
The PLAY/PAUSE INDICATOR on the base has
four settings:
1. OFF = the answering machine is off.
2. ON = the machine is on but no messages have
been recorded.
3. Light flashes quickly = new messages have
been received and not yet played.
4. Light flashes slowly = messages have been
played and saved.
NOTE:
■
Slow flashing also indicates active recording mode.
1
2
Adjust the base unit
VOLUME CONTROL
(located on the right side).
Press
NEW
on the base. The number of
new messages will be announced.
1
The PLAY/PAUSE INDICATOR on the base will
flash slowly when messages have been played
and saved.
PLAY ALL MESSAGES
Adjust the
VOLUME CONTROL
(located on the right side of the base).
2
Press
ALL
(on the base) to replay all new
plus saved messages. The total number of
messages will be announced.
3
You can repeat the current message.
REPEAT MESSAGES
1
Skip backward, message by message.
SKIP BACKWARD
1
During playback of messages, press
REPEAT
twice to skip backward to the
previous message. Press
REPEAT
each
time you want to skip backward through
messages.
1
NOTE:
■
Messages that were individually erased during
playback will be saved.
Press
SKIP
once to skip forward to the
next message.
SKIP FORWARD
1
You can temporarily pause message playback up
to five minutes. The TC-919 will not answer calls
in the Pause Mode.
PAUSE MESSAGE PLAYBACK
Press
ALL
or
NEW
during message
playback.
REPLAY ALL MESSAGES
You can erase specific messages while saving
others.
1
E
Message File offers a convenient way to store important messages, long messages or to separate
messages for business, personal use or for other users.
The green MESSAGE FILE INDICATOR on the
base has three settings when the answering
machine is turned on:
1. OFF = No messages have been filed.
2. Quickly flashes = New messages have been
transferred and not yet played.
3. Slowly flashes = File messages were played
and saved.
You can record a memo for another household member or as a reminder for yourself up to five
minutes in length. The memo will be stamped with the time and day it was recorded.
You will hear "
Please record message.
"
Begin speaking into the Microphone
(located at the bottom right-hand corner)
about 7" from the base unit.
Press
MEMO
to end the recording.
You can play new and saved messages privately
through the handset. Make sure the handset is in
the Standby Mode and the answering machine is
on.
1
Press
REMOTE/SCREEN
and then
PLAY
(
3
on the keypad). You will hear a
beep and the MESSAGES LED on the
handset will light solid.
2
Return the handset to the base cradle.
1
Press
ERASE
(
4
on the keypad) after
hearing “
End of messages.
”
2
The specific message will be erased 7
seconds after hearing “
End of Messages
”
unless
SAVE
(
1
on the keypad) is pressed.
If you do not press
SAVE
(
1
on the keypad) or
ERASE
(
4
on the keypad) while listening to
messages or after hearing “
End of messages,
”
the TC-919 will automatically save all messages.
3
1
After listening to messages, return the
handset to the base or wait seven seconds
to exit the Playback Mode.
Press
REMOTE/SCREEN
on the
handset and then
PLAY
(
3
on the handset
keypad) to playback your messages.
2
Press
MSG FILE
(
6
on the handset key-
pad) during message playback. The green
MESSAGE FILE INDICATOR on the base will
flash quickly to show that a message has
been transferred to Message File.
NOTE:
■
If
SAVE is pressed at the end of message playback,
then all messages will be saved in the main location,
and the messages that were transferred during
playback will also be saved in Message File.
1
1
H
Be sure the TALK INDICATOR on the
handset is not lit. (The handset must be in
Standby Mode.)
2
Press
REMOTE/SCREEN
on the
handset.
3
Press
MEMO
(
2
on the handset keypad).
4
The LOW BATT/RECORD INDICATOR
above the 2 button will light solid and you
will hear
“Please record a message”
through the earpiece. The TC-919 will
begin recording.
5
Press
MEMO
or
REMOTE/SCREEN
again to end the recording and return to
Standby Mode.
In the Standby Mode, the handset is inactive and
ready to receive calls. INDICATORS on the
handset will not be lit in Standby Mode.
Press
VOL +
or
VOL -
to change the
volume level of the handset during a
conversation or during message playback.
Each press of
VOL +
or
VOL -
will
increase or decrease the sound level to one
of four levels: Normal through High. When
you hang up the volume will reset to the
“Normal” setting.
1
2
3
When the handset is in the Talk Mode and
returned to the base unit, it will automatically
return to the Standby Mode and disconnect the
call. It is not necessary to press TALK on the
handset to disconnect the call.
1
Pick up the handset and press
TALK
.
2
Wait for dial tone and dial the phone
number. The CHARGING/LINE IN USE
INDICATOR on the base flashes slowly to
show that the handset is in use.
3
To hang up, press
TALK
again or return
the handset to the base unit.
NOTE:
■
When you return the handset to the base unit, you
are hanging up the phone (Standby Mode).
AUTODIAL
1
1
Press
TALK
on the handset twice (“off”
and “on”). Wait for dial tone and dial the
correct number.
1
1
Press
HOLD
. The TALK INDICATOR on
the handset flashes slowly.
Press
TALK
on the handset.
OR
1
2
3
Press
STORE
on the handset. You will
hear two beeps.
Enter one of the telephone numbers you
want to store in the AutoDial memory by
dialing it on the keypad. You will hear a
beep after entering each digit.
Press
AUTODIAL
.
It is assumed that the TC-919 is set to “PULSE”
(see "TONE/PULSE SWITCH SETTING".) If you
live in a pulse or rotary dialing area, you can use
tone to access a long distance service (i.e. Sprint
or MCI), bank by phone or any other service that
requires touchtone dialing.
Dial your telephone number and wait for
the line to connect. (You dialed your call in
Pulse Mode.)
Press
❋
❋
❋
❋
❋
TONE
on the handset to
temporarily change from Pulse to Tone
Mode.
Dial the tone numbers. This could be a
special service or access number.
1
1
2
5
You can use Remote Operation from most
touchtone or cellular phones to retrieve, replay,
erase and save messages.
3
4
TC-919 is shipped with the code set to 1-2-3.
To change your 3-Digit Remote Access Code:
Press
SKIP/+
or
REPEAT/-
until the first
number you select is announced.
Repeat steps 2 and 3 to set the second and
third remote code digits.
Call your answering machine from most cellular,
pay or touchtone telephones. Enter your 3-DIGIT
REMOTE ACCESS CODE immediately after the
greeting begins.
NOTE:
■
If the TC-919 does not respond when you enter your
code, try again after the beep.
After entering your 3-digit remote access code,
the number of new messages will be announced.
If new messages have been received, they will
play in the order of receipt. After all new
messages have played, you will hear “
End of
messages.
” Select another option or hang up.
NOTE:
■
Hang up anytime to cancel Remote Message
Playback. The TC-919 will automatically save all
messages, unless you choose to erase them.
1
SWITCH SETTINGS
The TC-919 has one switch on the side of the handset and three switches on the back of the base unit.
POWER SAVER/RINGER ON
The TC-919 is shipped with the HANDSET
RINGER SWITCH set to “PWR SAVER” (the ringer
is off). When set to PWR SAVER (power saver),
the battery power is conserved. Turn the handset
to “RINGER ON” before use.
RINGER ON - The ringer is on and the handset
will ring when an incoming call or paging
signal is received. When the handset is out of
the cradle, the rechargeable batteries will last
up to seven days in this mode (the PWR
SAVER is off).
POWER SAVER (PWR SAVER) ON - When an
incoming call or a paging signal is received the
handset will not ring, but all other handset
functions will operate. The rechargeable
batteries will last up to one month in this mode
(the ringer is off).
Set the
RINGER ON/OFF SWITCH
on the base to
control the telephone ringer. The base ringer is
preset to “RINGER ON.”
ON = Base ringer is turned on.
OFF = Base ringer is turned off, except if the
handset is charging and the handset ringer is
On. The handset will ring even if the base
ringer is set to Off.
BASE RINGER ON/OFF
RING SELECT
This switch configures the TC-919 to dial out
with either touchtone or pulse signals to match
the service supplied by your local telephone
company. The TC-919 is shipped with the TONE/
PULSE SWITCH set to “TONE.” If you have rotary
or pulse service, set this switch to “PULSE.”
PULSE = for Rotary dialing or Pulse services
TONE = for Touchtone service
TONE/PULSE
C
INITIAL SETUP
To select Greeting One or Greeting Two:
SELECT GREETINGS
Press
GREETING SELECT
(in the cradle)
You will hear “
Greeting One
” or “
Greeting
Two
” to indicate the current setting.
2
Pressing
GREETING SELECT
again will
change the setting to the other Greeting.
The TC-919 will now answer all calls with
the selected greeting.
NOTES:
■
If a greeting has not been recorded, all callers will
hear “
Record a message.”
RECORD GREETING ONE
Be sure the TC-919’s indicators are lit or
flashing.
2
Set the
VOLUME CONTROL
at midpoint
(located on right side of TC-919).
Press
GREETING RECORD
(located in
the cradle area). You will hear
"Please
Record Greeting One"
and a beep. Speak
loudly and clearly about 7" from the
microphone located at the lower right hand
corner of the base unit. The PLAY/PAUSE
INDICATOR on the Base unit will flash
slowly to confirm that recording is in
process.
NOTES:
■
If a greeting has not been recorded, callers will hear
“
Record a message.”
■
The greeting should be recorded without any
background noise.
■
The greeting should be recorded by only one person
speaking into the Microphone.
CHECK GREETING
1
2
Press
GREETING SELECT
until the
desired greeting is announced.
Press
GREETING CHECK
(located in
the cradle of TC-919.) The TC-919 will
play the greeting and reset to answer new
calls.
NOTE:
■
If a greeting has not been recorded, you will hear
“
No greeting. Please record greeting.” Callers will
hear “
Record a message.”
SET THE TIME/DAY
2
Press
SKIP/+
or
REPEAT/-
(on the
base) until the correct day is announced.
5
Press
TIME SET
again. The TC-919 will
announce the minutes.
6
Press
SKIP/+
to advance or
REPEAT/-
to reverse the minutes.
7
Press
TIME SET
again to end. The day
and time will be announced.
NOTE:
■
If the time and day have not been set, all messages
will be stamped with “
Sunday 12:00 a.m.”
2
The ringer will operate with the unit off,
but no messages will be recorded.
1
Press
TIME SET/CHECK
(in the cradle)
once. The day and time will be announced.
TALKING CLOCK
The TC-919 also functions as a clock.
D
PLAY/PAUSE INDICATOR
When messages have been received and not
played yet, the PLAY/PAUSE INDICATOR on the
base will flash quickly. To listen to new messages
only:
PLAY NEW MESSAGES
3
All new messages are played in the order
received. The message number, time and
day will be announced before each
message. After the last message is played,
you will hear, “
End of messages.
”
All messages are played in the order
received. The message number, time and
day will be announced before each message.
After the end of the last message you will
hear “
End of messages.
”
During playback of messages, press
REPEAT
(on the base) once to repeat the
current message.
You can skip forward through messages.
You have three options during pause:
2
2
2
Press
ALL
or
NEW
again to resume
listening to messages.
OR
Leave the TC-919 in Pause Mode. It will
automatically reset to answer calls after
five minutes. All messages will be saved.
OR
Press
ON/OFF
(in the cradle ) twice to
end pause. All messages will be saved.
To replay all messages,
1
Press
ALL
on the base after hearing, “
End
of messages.
”
If you do not press ERASE while listening to
messages or after playing them, the TC-919 will
automatically save all the messages.
AUTOMATIC SAVE
ERASE INDIVIDUAL MESSAGES
1
Press
ERASE
while listening to a specific
message.
2
If you change your mind and decide to
save the message, press
SAVE
at end of
message playback.
1
Press
ERASE
within seven seconds after
hearing “
End of messages
” to erase all
messages. You will hear “
Erase Messages
”.
ERASE ALL MESSAGES
NOTE:
■
Messages that were individually saved during
playback will be erased.
1
If you wish to save all messages, press
SAVE
within seven seconds after hearing
“End of messages”
or after pressing
ERASE
.
SAVE ALL MESSAGES
1
Press
TALK
on the handset or pick up any
extension phone to speak with the caller.
All messages will be automatically saved.
ANSWERING A CALL
DURING PLAYBACK
If you receive an incoming call during message
playback:
MESSAGE FILE
MESSAGE FILE INDICATOR
1
Press
ALL
or
NEW
on the base to
playback your messages.
TRANSFER MESSAGES TO
MESSAGE FILE
To store messages into Message File:
2
Press
MESSAGE FILE
during message
playback. You will hear
“Message Two
Transferred”
to indicate that a newly
transferred message has been saved in
Message File.
NOTE:
■
If
SAVE is pressed at the end of message playback,
then all messages will be saved in the main location,
and the messages that were transferred during
playback will also be saved in Message File.
1
Press
MESSAGE FILE
. The number of
messages in Message File will be
announced. Messages stored in this
location will be played.
PLAY ALL MESSAGES IN
MESSAGE FILE
When playing messages in Message File, you can
utilize the convenient playback features such as:
Pause, Skip/Repeat and Selective Save/Erase.
NOTES:
■
If there are no messages in Message File, you will
hear “
No file messages.”
■
After the last message is played you will hear “
End of
messages.”
RECORD A MEMO AT BASE
Press
MEMO
on the base unit.
F
Recorded memos are played along with the
incoming messages in the order in which they
were recorded.
G
HANDSET MESSAGE PLAYBACK
HANDSET MESSAGE
INDICATOR
In the Standby Mode, if you have messages, the
MESSAGES INDICATOR on the handset flashes
for 10 seconds after the handset is used. (In the
Standby Mode the TALK INDICATOR on the
handset is not lit.)
NOTE:
■
The MESSAGES INDICATOR on the handset does not
flash for messages stored in Message File.
MESSAGE PLAYBACK FROM
THE HANDSET
After listening to messages, to exit the Handset
Playback Mode:
2
OR
Press
REMOTE/SCREEN
again.
NOTE:
■
If you hang up during handset message retrieval, all
messages will be saved.
1
Press
REPEAT
(
❋
❋
❋
❋
❋
TONE
key) once to
repeat the current message.
REPEAT MESSAGES
You can repeat the current message.
1
Press
REPEAT
(
❋
❋
❋
❋
❋
TONE
key) twice to
skip backward to the previous message.
Press
REPEAT
each time you want to skip
backward through messages.
SKIP BACKWARD
Skip backward message by message.
1
Press
SKIP
(
#
key) once to skip forward
to the next message.
SKIP FORWARD
You can skip forward through messages.
1
SAVE ALL MESSAGES
Messages will be saved within seven seconds
after you hear the last message. To manually save
all messages,
Press
SAVE
(
1
on the handset keypad)
after hearing, "
End of messages
. "
ERASE ALL MESSAGES
All messages may be erased within seven
seconds after hearing the last message.
1
Press
ERASE
(
4
on the keypad) during
playback of a specific message.
ERASE INDIVIDUAL MESSAGES
Erase specific messages during Handset
message playback.
AUTOMATIC SAVE
2
1
Press
TALK
on the handset to answer the
incoming call. All messages will be saved.
ANSWER A CALL DURING
PLAYBACK
If a call comes in while you are playing your
messages through the handset, the answering
machine will not answer the call. Your phone will
ring if the HANDSET RINGER SWITCH is set to
“RINGER ON.”
To hang up and continue listening to your
messages, press
TALK, REMOTE/
SCREEN
and then
PLAY
(
3
on the
keypad).
TRANSFER MESSAGES TO
MESSAGE FILE
To store messages into Message File while
playing back messages through the handset:
PLAY ALL MESSAGES IN
MESSAGE FILE
When playing messages in Message File, you can
utilize the convenient playback features such as:
Skip/Repeat, and Selective Save/Erase.
1
Press
REMOTE/SCREEN
on the
handset and then
MSG FILE
(
6
on the
handset keypad). Messages stored in this
location will be played. After the last
message is played you will hear
“End of file
messages”
.
You can record a memo using the handset.
RECORD A MEMO
The TC-919 allows you to record important
telephone conversations.
CONVERSATION RECORD
Press
REMOTE/SCREEN
on the
handset during your phone conversation.
MEMO & CONVERSATION RECORD
Press
CONV
(
5
on the handset keypad).
The LOW BATT/RECORD INDICATOR
above the 2 button will light solid and the
TC-919 will begin recording.
Press
CONV
or
REMOTE/SCREEN
again to end the recording and return to
Standby Mode.
NOTE:
■
In certain states, it is unlawful and may lead to
criminal penalties to record any telephone
conversation without prior consent of all parties.
HANDSET TELEPHONE OPERATION
When the battery pack needs recharging, the
LOW BATT/RECORD Indicator on the handset will
flash. You may also notice a reduction in the
quality of your cordless handset communica-
tions. Return the cordless handset to the base
unit when the LOW BATT/RECORD INDICATOR is
flashing.
NOTE:
■
The batteries can be recharged many times, but if
you get a low battery indication even after 12-15
hours of charging, you should replace the battery
pack.
BATTERIES - If it becomes necessary to remove
or replace the batteries see "HANDSET NI-CAD
BATTERY INSTALLATION."
HANDSET LOW BATTERY
INDICATOR
STANDBY MODE
HANDSET VOLUME CONTROL
1. If you move out of the base unit’s operating
range, you will hear a warning tone. Move
closer to the base unit to deactivate the alarm.
If you remain out of range for too long, the
TC-919 will disconnect from the line.
2. If the handset loses its security code you will
also hear an alarm tone. To reset this security
code place the handset in the base unit for a
few seconds. Pick up the handset and try your
call again.
3. Interference from other appliances may also
cause the alarm to sound. To prevent
interference, move the base unit to another
location and vertically position the base unit
antenna.
ALARM
AUTO HANG UP
PLACING A CALL
MISDIALING A NUMBER
RECEIVING A CALL
When the phone rings, pick up the cordless
handset and press
TALK
. Speak to the
caller. To hang up, press
TALK
on the
handset or return the handset to the base
unit.
PLACING A CALL ON HOLD
NOTE:
■
If a call has been on hold for five minutes, the
TC-919 will automatically disconnect the call.
1
TAKING A CALL OFF HOLD
There are three ways to take a call off HOLD.
Press
HOLD
again on the handset.
1
OR
Pick up any extension phone that is
connected to the same line.
1
Pick up the handset, press
TALK
and then
REDIAL/PAUSE
. The TC-919 will
automatically redial the number.
LAST NUMBER REDIAL
The TC-919 remembers the last number you
dialed.
If you subscribe to a call waiting service and you
receive another call while using the phone, press
FLASH
(on the handset) to answer the second
call. Press
FLASH
again to return to the first
call. Flash may also be used on a business phone
system (CENTREX, PBX) for transferring calls.
FLASH/CALL WAITING
J
You may store up to 10 of your most frequently
dialed numbers in AutoDial memory. Autodial
numbers can be up to 24 digits in the Tone Mode
and the Pulse Mode.
STORING AUTODIAL
NUMBERS
4
5
Enter a one-digit keypad number (0-9) as
the AutoDial location for that number. You
will hear two beeps
.
Repeat steps 1-4 to store up to 10
AutoDial numbers.
6
Write the names and telephone numbers
of the people whose numbers you have
stored on the TC-919’s AutoDial index card
(located under the base unit).
NOTES:
■
To erase AutoDial numbers, store a new number in
the AutoDial location you wish to erase. For example,
you may store a one digit number to erase an old
phone number.
■
Autodial numbers are stored in the handset
permanently until they are changed. Autodial
numbers will not be lost when installing a new
handset battery.
■
You can store important emergency numbers in
AutoDial memory (police, fire, medical or 911 for
example) but Casio PhoneMate assumes no
responsibility for this feature.
Press
TALK
on the handset and wait for
the dial tone.
USING AUTODIAL
2
Press
AUTODIAL
.
3
Press the one-digit AutoDial location
number you wish to dial (0-9 on the
keypad). The TC-919 will dial your number
automatically. You will hear a series of
beeps during dialing.
TONE/PULSE MIXED DIALING
4
Hang up and the TC-919 automatically
returns to the Pulse Mode.
Pause is convenient for use on a business
telephone system (i.e.; PBX) when an 8 or 9 must
be dialed to reach an outside phone line. This
feature can also be used for a long distance
service (i.e.; MCI) where you have to wait for a
second dial tone before you continue dialing.
Follow instructions for "STORING AUTODIAL
NUMBERS."
PROGRAMMABLE PAUSE
Press
REDIAL/PAUSE
on the handset
when a pause is required. Each pause is
two seconds in length and counts as one
digit in the AutoDial memory.
REMOTE OPERATION
K
PROGRAM
REMOTE ACCESS CODE
Press
CODE SET/CHECK
(located in
the cradle ). You will hear the current
setting.
Press
CODE SET/CHECK
again within
five seconds after the audio speech. You
will hear, "
Enter remote code one.
" The
first remote code digit is announced.
Press
CODE SET/CHECK
again to end.
You will hear the newly programmed
3-digit access code announced.
REPEAT MESSAGES - Press
❋
❋
❋
❋
❋
once.
SKIP BACKWARD - Press
❋
❋
❋
❋
❋
twice.
SKIP FORWARD - Press
#
once.
REPLAY ALL MESSAGES - Press
1
.
SAVE ALL MESSAGES - Press
2
.
ERASE INDIVIDUAL MESSAGES - Press
3
as a
message plays back, you will hear, “
Erase
message
” and then the next message will play.
ERASE ALL MESSAGES - Press
3
after hearing,
“
End of messages
.”
AUTO SAVE - If you do not press SAVE or ERASE,
the TC-919 will automatically save all messages.
RECORD MEMO - Press
4
.
RECORD GREETING - Press
5
.
CHANGE GREETINGS - Press
6
.
PLAY MESSAGES IN MESSAGE FILE - Press
7
.
REMOTE MESSAGE RETRIEVAL
Frequent callers can skip your greeting when
they call to leave a message. Instruct them to
press
#
on their touchtone keypad any time after
the TC-919 answers their call.
GREETING BYPASS
REMOTE VOICE MENU
Enter
1 to play messages.
Enter
2 to save messages.
Enter
3 to erase messages.
Enter
4 to record message.
Enter
5 to record greeting.
Enter
6 for Greeting One (or Two)
Enter
7 to play file messages.
NOTE:
■
Remote menu items 1, 2 and 3 will not be announced
if no messages are received and stored. Remote
menu item 7 will not be announced if no messages
are stored in Message File.
REMOTE OPERATION OPTIONS
I
REMOTE TURN-ON
Call and let your phone ring 10 times or more.
The TC-919 will turn on and you will hear "Please
enter remote code."
1
When the phone rings, the TC-919 will answer
the call. You may use the handset to screen your
phone calls.
2
Press
REMOTE/SCREEN
to listen to
incoming calls from the cordless handset.
You will hear the TC-919 play your greeting
and your caller leave a message.
NOTE:
■
DO NOT press
ON/OFF on the base unit as you may
disconnect your caller.
CALL SCREENING
Be sure the PLAY/PAUSE INDICATOR on
the base unit is on.
3
4
Press
REMOTE/SCREEN
again to exit
Call Screening.
To speak to the caller, press
TALK
on the
handset. The unit will stop recording.
5
To hang up, press
TALK
or return the
handset to the base unit. The unit will
automatically reset to answer new calls.
You will hear “
Memory is Full
” after your greeting
is played. Enter your 3-DIGIT REMOTE ACCESS
CODE. After listening to messages, press
3
on
the keypad to erase them. If you have erased
messages, the TC-919 can now answer calls and
record new messages.
MEMORY FULL MESSAGE
RETRIEVAL
