Casio QW 5531 Operation Manual Download Page 4

Fast Forward/Fast Reverse

After pulling out the crown, rotating it quickly
in succession in either direction will cause the
hands to move forward or back at high speed.
While the hands are moving forward at high
speed, quickly rotating the crown in
succession again will increase the speed even
further.

Stopping Fast Forward/Fast Reverse

Rotate the crown in the direction opposite that
of the ongoing operation or press any button.

Note

If you do not perform any operation
for about two minutes after pulling
out the crown, crown operations will
automatically become disabled. If
that happens, push the crown back
in and then pull it out again.

Hand and Day Indicator

Movement

30

Day indicator

Day of the week hand

Day of the Week and Day Indicator
Operation

Changing the day setting of the watch will also
cause the day of the week hand to move in
conjunction with the day.

Day

It can take anywhere from about 10 to 40
seconds for the day indicator to change after
timekeeping reaches midnight. The day of
the week hand will move as the day indicator
changes.

The day may not be indicated correctly while
the watch’s crown is pulled out.

Solar Charging

This watch runs on power supplied from a

rechargeable (secondary) battery that is

charged by a solar panel. The solar panel is

integrated into the face of the watch, and

power is generated whenever the face is

exposed to light.

Charging the Watch

When you are not wearing the watch, put it in

a location where it is exposed to bright light.

While you are wearing the watch, make sure

that its face (solar panel) is not blocked from

the light by the sleeve of your clothing. Power

generation efficiency is reduced even when

the face of the watch is blocked only partially.

NO

YES

Important!

Depending on light intensity and

local conditions, the watch may

become hot to the touch when

exposed to light for charging. Take

care to avoid burn injury after

charging. Also, avoid charging the

watch under high-temperature

conditions like the ones described

below.

On the dashboard of a vehicle

parked in the sun

Near an incandescent light bulb or

other source of heat

Under direct sunlight or in other

hot areas for long periods

Checking the Charge Level

Immediately after you press (C) to return to the

Timekeeping Mode, the day of the week hand

will indicate the battery charge level. After a

short while, the day of the week hand will

return to indicating the current day of the

week.

30

A

Good (high charge)

B

Good (medium charge)

C

Low Battery

Remaining Charge and Dead Battery

You can determine if the charge level is low by

checking the hand movement. Functions

become disabled as battery power goes low.

Important!

Should battery go low or go dead,

expose the face (solar panel) to light

as soon as possible.

Note

Exposing the watch face to light after

the battery goes dead will cause the

second hand to revolve

counterclockwise until it stops at

second 57. This indicates charging

has started.

Operation Guide 5531

4

Summary of Contents for QW 5531



























Reviews: