manualshive.com logo in svg

Casio QW-2802, Service Manual, Page: 14 / 17

Share
Download
Casio QW-2802 Service Manual Download Page 14

5. PARTS LIST: MODULE QW-2802

Note: 1.  Prices and specifications are subject to change without prior notice.

2.  Spare parts are classified as follows according to their importance in after-sales service.

A Rank ---------------------------------------- Very Important
B Rank ---------------------------------------- Important
C Rank ---------------------------------------- Less important

3.  Batteries in Bulk pack on the tray will be supplied from our  Overseas Spare Parts Section under charge basis
     Batteries in Blister pack will be supplied from our Sales Department.
4.  As for order/supply of spare parts, refer to the separate publication "GUIDE BOOK for spare parts supply".

Item

Code No.

Parts Name

Specification

Applicable

Q R

MODULE/WITHOUT MOVEMENT

QW-2802AT-01

STR-500-1V/2V/4V/9V

< The module QW-2802 is "built-in type" which is assembled directly to
   the case, therefore the module as the spare parts is not available. >

1

1012 5268 LCD

C2802-01P

QW-2802AT-01

1

A

2

1008 9590 EL

YEL-2534-A-00

QW-2802AT-01

1

A

3

7640 6976 PCB ASS'Y

RJQ514861*001V01TK

QW-2802AT-01

1

A

4

1009 7666 CAPACITOR/TRIMMER

CTZ2E-25C-W2-P

QW-2802AT-01

1

B

5

7110 6323 OSCILLATOR/CRYSTAL

DT-26S11

QW-2802AT-01

1

B

6

1006 5657 BATTERY/STORAGE

CTL1616

QW-2802AT-01

1

B

7

7231 1913 CONTACT/BATTERY(-)

Q359948B-2

QW-2802AT-01

1

C

8

7218 0438 CUSHION/524

Q411459-1

QW-2802AT-01

1

C

9

1008 3364 HOLDER/BATTERY

Q254197A-2

QW-2802AT-01

1

C

10

1008 2102 HOUSING

Q152370-1

QW-2802AT-01

1

C

11

1008 2135 INTERCONNECTOR

Q469546-1

QW-2802AT-01

2

C

12

1006 5664 LABEL 2368

Q468543A-1

QW-2802AT-01

1

C

13

7105 5275 SENSOR/TILT

TS-2418-P

QW-2802AT-01

1

B

14

1009 9862 SHEET/INSULATION

Q470524-1

QW-2802AT-01

1

C

15

1008 2132 SPACER

Q152368-1

QW-2802AT-01

1

C

16

1008 2133 SPACER

Q152369A-1

QW-2802AT-01

1

C

17

7230 0616 SPRING/COIL 1199-1

Q437728B-1

QW-2802AT-01

2

B

18

1008 2134 SPRING/COIL 2534-1

Q469421-1

QW-2802AT-01

2

B

19

7230 0644 SPRING/COIL 785-1

Q439335-1

QW-2802AT-01

1

B

20

1008 4578 SUPPORTER/PCB ASS'Y

Q152367-2

QW-2802AT-01

1

C

For the prices and minimum order/supply quantities of the above parts, refer to the Parts Price List P.P.L.-600.

   Notes:     Q -  Used quantity

R -  Rank

— 12 —

Summary of Contents for QW-2802


















Reviews:

No comments