Operation Guide 3068
3
To configure countdown timer settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the
countdown start time setting starts to flash, which
indicates the setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
Start
Time
Reset
Time
Timer
Type
3. When the setting you want to change is flashing, use
D
and
B
to change it as
described below.
l l lll
ll
llll
ll
ll
ll
l
4. Press
A
to exit the setting screen.
•
The reset time setting must be less than the countdown start time setting.
Setting
Start Time
Reset Time
Timer Type
Button Operations
Use
D
(+) and
B
(–) to change the setting.
•
You can set a start time in the range of 1 to 60 minutes
in 1-minute increments.
Use
D
(+) and
B
(–) to change the setting.
•
You can set a reset time in the range of 1 to 5 minutes
in 1-minute increments.
Press
D
to toggle between the auto-repeat mode (
)
and the elapsed time mode (
).
Screen
To use the countdown timer
In the Countdown Timer Mode, press
D
to start the
countdown timer.
•
The countdown timer measurement operation continues
even if you exit the Countdown Timer Mode.
•
The table below describes button operations you can
perform to control countdown operations.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press
D
.
Press
D
again.
While the countdown is
stopped, press
A
.
Press
A
.
Press
D
.
•
The table below describes button operations you can perform during an elapsed
time measurement operation in the elapsed time mode.
To do this:
Stop the elapsed time operation
Resume a stopped elapsed time operation
Display the countdown start time
Stop the elapsed time operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press
D
.
Press
D
again.
While the elapsed time is
stopped, press
A
.
Press
A
.
Press
D
.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 99 hours, 59
minutes, 59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
.
Minutes
Seconds
Hours
1/100
second
Mode
indicator
To measure times with the stopwatch
D
Start
Stop
Elapsed Time
➤
Re-start
Clear
D
➤
D
➤
D
➤
A
Split Time
D
Start
Split
(
SPL
displayed)
➤
Split release
Clear
A
➤
Stop
A
➤
D
➤
A
Two Finishes
D
Start
Split
➤
Stop
Clear
A
➤
Split release
D
➤
A
➤
A
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
World Time
The World Time Mode shows you the current time in 32
cities (30 time zones) around the world.
•
If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
C
.
Current time in
selected city
To view the time in another city
While in the World Time Mode, press
D
to scroll eastward through the city codes
(time zones).
•
For full information on city codes, see “UTC Differential/City Code List”.
City code
Timekeeping
Mode time
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
A
to toggle Daylight Saving Time (
DST
indicator displayed) and Standard Time (
DST
indicator
not displayed).
•
The
DST
indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
•
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
DST indicator
Alarms
The Alarm Mode gives you a choice of three one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
SIG
) on and off.
•
There are four alarms numbered
AL1
through
AL3
,
and
SNZ
. You can configure
SNZ
as a snooze alarm
only. Alarms
AL1
through
AL3
can be used as one-
time alarms only.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
Alarm time
(Hour : Minutes)
Alarm
number
Timekeeping
Mode time
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1
AL2
AL3
SIG
SNZ
2. After you select an alarm, hold down
A
until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•
This operation turns on the alarm automatically.
3. Use
C
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to change it.
5. Press
A
to exit the setting screen.
•
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (
P
indicator).
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
•
Pressing any button stops the alarm tone operation.
•
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the snooze alarm setting screen
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use
D
to select an alarm.
2. Press
A
to toggle it on and off.
•
Turning on a one-time alarm (
AL1
,
AL2
,
AL3
)
displays the alarm on indicator on its Alarm Mode
screen. Turning on the snooze alarm (
SNZ
) displays
the alarm on indicator and snooze alarm indicator on its
Alarm Mode screen.
•
In all modes, the alarm on indicator is shown for any
alarm that is currently turned on. When the snooze
alarm is on, the snooze alarm indicator and the alarm
on indicator are displayed in all modes.
•
The alarm on indicator flashes while the alarm is
sounding.
•
The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Snooze alarm indicator
Alarm on indicator
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select the Hourly Time
Signal (
SIG
).
2. Press
A
to toggle it on (Hourly Time Signal on
indicator
displayed) and off (Hourly Time Signal on
indicator
not displayed).
•
The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
Hourly time signal
on indicator
Stop