— 5 —
■
T
o
position the watch for optimum
reception
Remove the watch from your wrist and place it somewhere so its
top (12 o
’clock side, where the antenna is located) is facing
approximately in the direction of the signal transmitter
. Keep the
watch away from metal objects.
Resin band
Metal band
•
Orienting the watch so it is sideways to the transmitter makes it
more dif
ficult to receive the signal.
•
Do not move the watch while it is receiving the calibration signal.
■
T
ime Required for Reception
A calibration signal receive operation takes anywhere from about
two to five minutes.
•
Note that when
“AUTO
” (Auto Select) is specified as the
transmitter selection mode, signal reception can take up to
12 minutes
.
•
See
“Configuring Auto
Receive
Settings
” for more information.
■
T
o
perform manual receive
In the T
imekeeping Mode, hold
down the
DDDDD
button for about
two seconds.
•
The watch will beep and
reception will start.
An indicator
will appear on the display to
indicate reception conditions.
■
T
o
interrupt reception
Press the
DDDDD
button.
•
All other buttons besides
D
are disabled during signal reception.
When reception is successful
The watch terminates reception and adjusts the current time. Next
it beeps and then displays the date and time that the adjustment
was performed.
•
The watch will return to the
T
imekeeping Mode screen if you
press the
D
button or if you do not perform any operation for
about two or three minutes.
Reception Error (ERR Indicator)
The watch does not adjust its current time setting, and displays
“ERR
” when signal reception is unsuccessful for some reason.
•
The watch will return to the
T
imekeeping Mode screen if you
press the
D
button or if you do not perform any operation for
about two or three minutes.
■
Receive Indicator
The receive indicator cycles from
“Unstable
” through
“Stable
” as
shown below while reception is in
progress. How far it cycles depends
on the signal strength. Keep the
watch in a location where reception
is stable while reception is in
progress.
White-On-
Black
Black-On-
White
Unstable
Stable
•
Even under optimum reception conditions, it can take about 10
seconds for reception to stabilize.
•
Use the receive indicator to check reception status and to
determine the best location for signal reception.
•
Note that weather
, the time of day
, surroundings, and other
factors can all af
fect reception.
Receive Indicator
■
T
o
view the last reception date and time
In the T
imekeeping Mode, press the
DDDDD
button.
•
This causes the display to start alternating between the last
reception date screen and the last reception time screen at two-
second intervals.
•
“–
–
–”
will appear in the digital display if the watch has not been
able to perform any signal reception successfully
.
•
T
o
return to the
T
imekeeping Mode, press the
D
button again.
•
The watch will return to the
T
imekeeping Mode automatically if
you do not perform any operation for about two or three minutes.
Last reception
date
2 seconds
Last reception
time
3.
Use the
DDDDD
and
BBBBB
buttons
to cycle through the
available auto receive
settings.
4.
When the setting is the
way you want, press the
AAAAA
button.
•
This will exit the setting
screen and return to the last
reception date and time
screens.
•
T
o
return to the
T
imekeeping
Mode, press the
D
button
again.
•
The watch will return to the
T
imekeeping Mode
automatically if you do not
perform any operation for
about two or three minutes.
Configuring Auto
Receive
Settings
Use the procedure below to turn auto receive of the time
calibration signal on or of
f. When
TYO
(T
okyo) or
SEL
(Seoul) is
selected as your Home City
, you can also specify the transmitter
selection mode, which controls which Japanese transmitter signal
should be used for time calibration.
•
For information about selecting your Home City
, see
“Configuring
Home T
ime Settings
”.
•
The initial factory default settings for auto receive are Home City =
TYO
(T
okyo);
Auto Receive = On; T
ransmitter =
AUT
O
•
The following procedure can be performed only when
TYO
,
SEL
,
NYC
,
CHI
,
DEN
, or
LAX
is selected as the Home City
.
■
T
o
configure auto receive settings
1.
In the T
imekeeping Mode,
press the
DDDDD
button.
•
This causes the display to
start alternating between the
last reception date and time
screens.
•
The watch will return to the
T
imekeeping Mode
automatically if you do not
perform any operation for
about two or three minutes.
2.
Hold down the
AAAAA
button
for about two seconds.
•
This will cause the current
auto receive setting to flash
on the display
.
Auto Receive Settings when the Home City is TYO
or SEL
•
AUT
O
Auto receive turned on with automatic selection of either the
Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal
(60kHz), whichever is strongest.
•
J40
Auto receive turned on for the Mt. Otakadoya signal (40kHz).
•
J60
Auto receive turned on for the Mt. Hagane signal (60kHz).
•
OFF
Auto receive turned of
f.
Auto Receive Settings when the Home City is NYC,
CHI, DEN, or LAX
•
ON
Auto receive turned on for the Ft. Collins, Colorado signal.
•
OFF
Auto receive turned of
f.
Calibration Signal Reception
Precautions
•
Auto reception can be performed while the watch is in the
T
imekeeping Mode or W
orld T
ime Mode only
.
•
Reception cannot be performed while
T
imer Mode countdown is in
progress.
•
Pressing any button while auto reception is in progress will cause
the watch to beep and then exit the receive operation.
•
Make sure you are within the range of the calibration signal
transmitter before performing the reception operation. Remember
that geographic contours, nearby buildings, seasonal conditions,
the time of day
, can even make reception impossible even when
you are within range of the transmitter
.
•
Proper reception may be impossible if there is something blocking
the signal. If reception is unsuccessful, try again.
•
This watch is designed to adjust its current time setting in
accordance with the calibration signal transmitted in Japan and
the United States only
. It operates like a standard (non-radio
controlled) watch outside of the range of the receivable time
calibration signal transmitters.
•
When the watch is unable to adjust its time signal using the
calibration signal for some reason, timekeeping accuracy is within
±
15 seconds per month.
•
Strong electrostatic charge can cause timekeeping error
.
•
Signal reception is cancelled if the alarm starts to sound while it is
being performed.
•
The watch
’s calendar shows dates up to the year 2099.
Attempting a receive operation after that causes an error
.
