background image

 

26

 

2.7  DT-5022CHG Dual Battery Charger 

Basic Block 

Table 2.9 

Item Specification 

Remark 

Basic function 

Rechargeable battery pack 

HA-A20BAT Battery 

pack 

 

DT-5025LBAT Large-capacity battery pack 

Dedicated batteries only.

AC adaptor 

AD-S45150AU 

Input 100 to 230VAC (W/US power cord) 

 

 

AD-S45150AE 

Input 100 to 230VAC (W/European power 
cord) 

Dedicated AC adaptors 
for the charger 

 

Interface Block 

Table 2.10 

Item Specification 

 

Remark 

 

Input terminals for joint block 

1: VIN2 

Rated DC16V Input voltage 8 to 20 

 

2: VIN3 

Rated DC16V Input voltage 8 to 20 

 

3: NC 

NC 

 

 

4: GND 

GND 

 

Output terminals for joint block 

1: VOUT1 

DC16V 

Output terminal from 1

st

 unit when 

AC adaptor is used. 

2: VOUT2 

DC16V 

Output terminal from 2

nd

 unit 

3: NC 

NC 

 

 

4: GND 

GND 

 

No. of joint-able units 

3 units (x DT-5022CHG)   

 

 

Power Supply Block 

Table 2.11 

Item Specification 

Remark 

Input 

Rated voltage 

DC 16V 

 

 

Input voltage 

DC 8.0 to 20V 

 

Rated output 

Rated output voltage 

DC 4.22V 

 

 

Rated output current 

DC 1,600 mA 

 

Input consumption current 
 

Input consumption current 

0.65 A 

When input voltage is at 16V. 

Continue.

Summary of Contents for DT-X11 Series




















































Reviews: