User’s Guide 5544 (MTG)
E-15
Configuring City Settings
Important!
x
In order to prevent loss of water resistance and damage due to impact, make sure that the crown is
fully pushed in to its normal position after operating it.
x
For details about summer time settings and time zone settings, refer to the Operation Guide available
at the CASIO website.
http://world.casio.com/manual/wat/
E-14
Using the Watch in a Medical Facility or Aircraft
x
Disable auto time adjustment whenever you are in a medical facility, and aircraft, in any other area
where radio wave reception and connection with a phone are prohibited or restricted.
x
Disabling auto time adjustment disables time calibration signal auto receive and auto connection with
a phone.
x
In the Timekeeping Mode, press
B
once and then pull out the crown to the first click. The second
hand will move to
Y (YES)
(auto receive enabled) or
N (NO)
(auto receive disabled). To disable
auto time adjustment, rotate the crown to move the second hand to
N (NO)
. To enable auto time
adjustment, rotate the crown to move the second hand to
Y (YES)
. After the setting is the way you
want, push the crown back in to its normal position.
30
E-13
C
Stopwatch Mode
Countdown Timer Mode
30
x
Start
x
Stop
Seconds
x
Reset
x
Enters the
Countdown
Timer Mode
Points to ST
Hours
Minutes
Hours
(0 to 24)
C
30
x
Start
x
Stop
Seconds
x
Reset
x
Enters the
Alarm Mode
Points to TR
Hours
Minutes
Hours
(0 to 24)
C
Alarm Mode
* The A-side of the dial indicates an a.m. time, while
the P-side indicates a p.m. time.
x
Hold down
C
for about four seconds to establish
a Bluetooth connection with a phone. For details,
refer to the Operation Guide available at the CASIO
website.
http://world.casio.com/manual/wat/
30
x
Illumination
Alarm on
x
Alarm on/off
x
Enters the
Timekeeping
Mode
Points to AL
Hours
Minutes
Hours
(0 to 24)
x
Holding down
C
for two seconds in any mode returns to the Timekeeping Mode.
E-12
Mode Reference Guide
x
Use
C
to navigate between modes.
Timekeeping Mode
30
Minute hand
Day of the week
hand
24-hour hand
Hour hand
Second hand
Day Indicator
Crown
C
B
A
World time hour hand
World time 24-hour hand*
World time minute hand
x
Pressing
A
turns on the illumination.
x
To swap your Home Time with the World
time, hold down
A
for three seconds.
x
To view the result of last time calibration by
time signal reception or Mobile Link, press
B
once.
x
To trigger a time calibration by Mobile Link
manually, hold down
B
for 0.5 seconds.
x
To trigger a time calibration signal reception
operation manually, hold down
B
for
1.5 seconds.
x
To search for the phone paired with the
watch, hold down
B
for 3.5 seconds.
C
E-11
Time Calibration Signal Manual Receive
1. Hold down
B
for 1.5 seconds until the second hand moves to
RC
(Receive). If the second hand is a position other than
RC
, keep
B
depressed until it moves to
RC
.
2. Place the watch near a window.
x
The time setting will be adjusted automatically when a signal receive
operation is successful.
x
Calibration signal reception normally takes anywhere from about two
to 10 minutes. It can take as long as 20 minutes.
x
Best reception is in the middle of the night.
x
If you are unable to receive a signal, check the Operation Guide
available at the CASIO website to ensure the watch is in a suitable
location.
http://world.casio.com/manual/wat/
30
Second hand
E-10
Time Calibration Signal Auto Receive
Important!
x
To perform time calibration signal auto receive, the watch must be in the Timekeeping Mode. See
“Mode Reference Guide” (page E-12).
●
Leave the watch in a location that is appropriate for time calibration signal reception between
the hours of midnight and 5:00 a.m. See “Appropriate Signal Reception Location (Time
Calibration Signal)” (page E-9).
x
The second hand will point to
RC
while time calibration signal reception is in progress.
x
Reception normally takes anywhere from about two to ten minutes, but it can take as long as
20 minutes.
x
When the receive operation is successful, the time and day settings will be adjusted automatically.
E-9
Timekeeping (Based on a Time Calibration Signal)
Appropriate Signal Reception Location (Time Calibration Signal)
x
Keep the watch away from metal and position it so its 6 o’clock side is
facing a window. Avoid moving the watch as much as possible and do
not perform any watch operations while a signal receive operation is in
progress.
●
You may experience time calibration signal reception problems in
the areas described below.
- Among or near buildings
- While riding in a vehicle
- Near household appliances, office machines, mobile phones, etc.
- On a construction site, in an airport, or any other location where radio
wave interference occurs
- Near high-voltage lines
- In mountainous areas or behind a mountain
x
Always check the time setting on the day there should be a switch
between standard time and summer time (DST). If the setting is not
correct (due to signal reception failure), turn DST on or off manually as
required.
6 o’clock
E-8
Timekeeping (Current Time and Day Adjustment)
●
Timekeeping is kept accurate using information provided by a time calibration signal and by
communication with a mobile phone.
x
Time calibration signals can be received using Auto Receive or Manual Receive (page E-9).
x
To set the current time and day, normally use the procedure under “Time Calibration Signal Auto
Receive” (page E-10).
x
For information about how to adjust time using a phone, refer to the Operation Guide available at
the website below.
http://world.casio.com/manual/wat/
x
If you are in an area where a time calibration signal cannot be received or if you cannot connect
with a phone for some reason, adjust time and date settings manually (page E-18).
Important!
x
If you feel that the current time and/or day indicator are not in the correct positions, you can adjust
their alignment. For details, see the Operation Guide available at the CASIO website.
x
Time calibration signal reception is normally possible in the areas below.
Japan, China, North America, Europe
For details, see the Operation Guide available at the CASIO website.
x
For details about how to configure the following settings manually, refer to the Operation Guide
available at the CASIO website: Home Time summer time setting, current time setting, date setting.
http://world.casio.com/manual/wat/
