Casio 5083, Operation Manual, Page: 5 / 5

5
Operation Guide 5083 (OC)
When adjusting a hand or the date home position, it is recommended that after you move to a proper

home position, you press
B
to move the setting back one step. Next, press
D
again to return it to the
home position. This helps to ensure better home position adjustment accuracy.
After confi rming that the 3.
x
Second Hand is at the proper home position, press
C
. This will switch to
z
Hour Hand and
c
Minute Hand home position
adjustment.
The
 z
Hour Hand and
c
Minute Hand are at their proper home positions if
they both move to 12 o’clock. If the hands are not positioned correctly, use
D
(+) and
B
(–) to move them to their proper home positions.
After confi rming that the 4.
z
Hour Hand and
c
Minute Hand are in their correct
home positions, press
C
. This will switch to
b
Right Dial Hands home position
adjustment.
The
 b
Right Dial Hands are at their proper home positions if they both move
to 24 . If the hands are not positioned correctly, use
D
(+) and
B
(–) to move
them to 24 .
After confi rming that the 5.
b
Right Dial Hands are in the correct home position,
press
C
. This will advance to
v
Left Dial Hand home position adjustment.
The

v
Left Dial Hand
is in the correct home position if it is pointing at 12
o’clock. If it isn’t, use
D
(+) and
B
(–) to move it to 12 o’clock.
After confi rming that the 6.
v
Left Dial Hand is in the correct home position, press
C
. This will advance to day home position adjustment.
The
 n
Day is in the correct home position if it shows 1 . If it doesn’t, use
D
(+)
and
B
(–) to change the day to 1 .
Press 7.
A
to return to the Timekeeping Mode.
The
 n
Day moves to the current day, and then the
z
Hour Hand and the
c
Minute Hand will move to the current time. Wait until everything stops
moving.
Troubleshooting
Hand Movement and Position
■
I lost track of what mode the watch is in.
Refer to “To select a mode”. To return directly to the Timekeeping Mode from any other mode, hold down
C
for about two seconds.
■
The
x
Second Hand
is moving at two second intervals.
■
All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the
x
Second Hand starts moving normally, at one-second
intervals.
■
The hands of the watch suddenly start moving at high speed, even when I do not perform any
operation.
This could be due to any one of the following causes. In all cases, the hand movement does not indicate
malfunction, and should stop shortly.
The watch is recovering from a sleep state.

The time setting is being adjusted following a successful auto time calibration signal receive operation.

The watch is returning to the Timekeeping Mode automatically from the Alarm Mode.

■
Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode. Do not perform any operation until the hands return to
their normal positions (in about 15 minutes). The hands should return to their correct positions when power
recovers. To help power recover, leave the watch in a location where it is exposed to light.
■
The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it, if necessary.
■
The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is possible, see “To confi gure
Home City settings”.
If you are using the watch in an area where time calibration signal reception is not possible, you may need to
change your Home City’s
STD (standard time)/ DST (daylight saving/summer time) setting manually. Use the
procedure under “To toggle the Home City time between standard time and daylight saving time” to change the
STD / DST setting.
■
The hands and/or day indications are off.
This could indicate that the watch has been exposed to magnetism or strong impact, which has caused
problems with proper hand and day alignment. Adjust the watch’s hand and day home position alignment.
World Time Mode
■
The World Time indicated by the
b
Right Dial Hands in the World Time Mode is one hour off from the
actual time in the selected time zone.
The STD (standard time)/ DST (daylight saving/summer time) setting of the selected World Time City may be
wrong. Select the correct STD (standard time)/ DST (daylight saving/summer time) setting.
■
The World Time indicated by the
b
Right Dial Hands
in the World Time Mode is off.
Your Home City settings may be wrong. Check your Home City settings and correct them, if necessary.
Charging
■
The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3. Continue exposing the watch to light until the
x
Second Hand starts moving normally (at one-second intervals).
■
The
x
Second Hand starts to move at one-second intervals, but then suddenly returns to moving at
two-second intervals.
The watch probably is not suffi ciently charged yet. Continue keeping it exposed to light.
Time Calibration Signal
The information in this section applies only when LON , PAR , ATH , HNL , ANC , LAX , DEN , CHI , NYC , HKG ,
or TYO is selected as the Home City. You need to adjust the current time manually when any other city is
selected as the Home City.
■
The
x
Second Hand indicates NO (N) when I check the result of the latest receive operation.
Possible Cause Remedy
You are wearing or moving the watch, or performing a

button operation during the signal receive operation.
The watch is in an area with poor reception conditions.

Keep the watch in an area where reception conditions are
good while the signal receive operation is being performed.
You are in an area where signal reception is not possible
for some reason.
See “Approximate Reception Ranges”.
The calibration signal is not being transmitted for some
reason.
Check the website of the organization that maintains the

time calibration signal in your area for information about
its down times.
Try again later.

■
The current time setting changes after I set it manually.
You may have the watch confi gured for Auto Receive of the time calibration signal, which will cause the time
to be adjusted automatically according to your currently selected Home City. If this results in the wrong time
setting, check your Home City setting and correct it, if necessary.
+ B
*
6 > *
■
The current time setting is off by one hour.
Possible Cause Remedy
Signal reception on a day for switching between STD
(standard time)/ DST (daylight saving/summer time) may
have failed for some reason.
Perform the operation under “To get ready for a receive
operation”. The time setting will be adjusted automatically as
soon as signal reception is successful.
If you are unable to receive the time calibration signal,
change the
STD (standard time)/ DST (daylight saving/
summer time) setting manually.
■
Auto Receive is not performed or I cannot perform Manual Receive.
Possible Cause Remedy
The watch is in the Stopwatch Mode.
Auto Receive is not performed while the watch is in the
Stopwatch Mode. Hold down
C
for about two seconds to
enter the Timekeeping Mode.
Your Home City setting is wrong. Check your Home City setting and correct it, if necessary.
There is not enough power for signal reception. Expose the watch to light to charge it.
■
Signal reception is being performed successfully, but the time and/or day is wrong.
Possible Cause Remedy
Your Home City setting is wrong. Check your Home City setting and correct it, if necessary.
The watch may have been exposed to magnetism or
strong impact, which has caused problems with proper
hand and day alignment.
Adjust the watch’s hand and day home positions.
Specifi cations
Accuracy at normal temperature: ± 15 seconds a month (with no signal calibration)
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, day, day of the week
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated Universal Time); Daylight
Saving Time (summer time) / Standard Time
Time Calibration Signal Reception: Auto receive up to six times a day (5 times a day for the Chinese
calibration signal; Remaining auto receives cancelled as soon as one is successful); Manual
receive
Receivable Time Calibration Signals:
Mainfl ingen, Germany (Call Sign: DCF77, Frequency: 77.5 kHz); Anthorn, England (Call Sign:
MSF, Frequency: 60.0 kHz); Fukushima, Japan (Call Sign: JJY, Frequency: 40.0 kHz); Fukuoka/
Saga, Japan (Call Sign: JJY, Frequency: 60.0 kHz); Fort Collins, Colorado, the United States
(Call Sign: WWVB, Frequency: 60.0 kHz); Shangqiu City, Henan Province, China (Call Sign:
BPC, Frequency: 68.5 kHz)
Stopwatch: Measuring capacity: 23’59.99”
Measuring unit: 1/100 second
Measuring mode: Elapsed time, split time
World Time: 29 cities (29 time zones) and Coordinated Universal Time
Other: Standard Time/Daylight Saving Time (summer time); Home City/World Time City swapping
Alarm: Daily alarm
Other: Power Saving; Auto Correction of Hand Home Positions
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 5 months (no exposure to light after a full charge; 10 seconds alarm
beeper operation and one signal reception of approximately 4 minutes per day)
City Code Table
City Code City
UTC Offset/
GMT Differential
PPG Pago Pago –11
HNL Honolulu –10
ANC Anchorage –9
LAX Los Angeles –8
DEN Denver –7
CHI Chicago –6
NYC New York –5
SCL Santiago –4
RIO Rio De Janeiro –3
FEN Fernando de Noronha –2
RAI Praia –1
UTC
0
LON London
PAR Paris +1
ATH Athens +2
JED Jeddah +3
THR Tehran +3.5
DXB Dubai +4
KBL Kabul +4.5
KHI Karachi +5
DEL Delhi +5.5
DAC Dhaka +6
RGN Yangon +6.5
BKK Bangkok +7
HKG Hong Kong +8
TYO Tokyo +9
ADL Adelaide +9.5
SYD Sydney +10
NOU Noumea +11
WLG Wellington +12
 
Based on data as of December 2008.
 
The rules governing global times (GMT differential and UTC offset) and summer time are determined by
each individual country.