2
Operation Guide 3794
To adjust the analog time
1. In the Timekeeping Mode, press
B
four times to enter
the Hand Setting Mode.
2. Hold down
C
until the current digital time starts to
flash, which indicates the analog setting screen.
When you want to do this:
Move the hand setting forward
20 seconds
Move the hand setting a short way
forward at high speed
Move the hand setting a long way
forward at high speed
Perform this button operation:
•
Press
A
.
•
Hold down
A
.
•
Release
A
when the hands reach the setting you
want.
•
While holding down
A
to move the hands at high
speed, press
B
to lock the high-speed hand
movement.
•
To stop the hand movement, press any button.
•
Hand movement stops automatically if the hour hand
makes one full (12-hour) revolution or if a daily alarm
or Hourly Time Signal starts to sound.
3. Use
A
and
B
to adjust the analog setting as described below.
4. Press
C
to exit the setting screen.
•
The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
•
To return to the Timekeeping Mode, press
B
.
City code
Current time for the
selected city code
World Time
World Time digitally displays the current time in 48 cities
(29 time zones) around the world.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
B
.
To view the time in another city
1. In the World Time Mode, press
A
to display the
currently selected city code.
2. While the city code is displayed, press
A
to scroll
eastwardly through the city codes.
•
The city code is displayed for about one second, and
then it is replaced with the current time for that city
code.
•
For full information about city codes, see the “City Code
Table”.
•
If the current time shown for a city is wrong, it probably means there is a problem
with your Timekeeping Mode time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary adjustments.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
A
to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down
C
for about three seconds to toggle
between Daylight Saving Time (DST indicator
displayed) and Standard Time (DST indicator
not
displayed).
DST indicator
•
Though illumination will also turn on when you press
C
, keep the button held down
to toggle between Daylight Saving Time and Standard Time.
•
The DST indicator is on the display whenever you display a city code for which
Daylight Saving Time is turned on.
•
Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
•
Note that you cannnot use the World Time Mode to change the DST setting of the
Home City code you currently have selected in the Timekeeping Mode. See “To
toggle the Timekeeping Mode digital time between DST and Standard Time” for
information about turning the Home City code DST setting on and off.
1/100 second
Minutes Seconds
Stopwatch
The stopwatch lets you measure elapsed time.
•
The display range of the stopwatch is 59 minutes,
59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
B
.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Hold down
Alarm on indicator
Alarm time
(Hour : Minutes)
Alarm
When the alarm is turned on, the alarm tone sounds when
the alarm time is reached.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
B
.
To set an alarm time
1. In the Alarm Mode, hold down
C
until the hour setting
of the alarm time starts to flash, which indicates the
setting screen.
•
Though illumination will also turn on when you press
C
, keep the button held down until the hour setting of
the alarm time flashes.
•
This operation automatically turns on the alarm.
2. Press
B
to move the flashing between the hour and
minute settings.
3. While a setting is flashing, use
A
(+) to change it.
•
When setting the alarm time using the 12-hour format,
take care to set the time correctly as a.m. (no
indicator) or p.m. (
P
indicator).
4. Press
C
to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in.
•
To stop the alarm tone after it starts to sound, press any button.
To test the alarm
In the Alarm Mode, hold down
A
to sound the alarm.
To turn the daily alarm and the Hourly Time Signal on and off
In the Alarm Mode, press
A
to cycle through the settings shown below.
Dark figures on a light background
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
Light figures on a dark background
Alarm Off
Signal Off
Alarm On
Signal Off
Alarm Off
Signal On
Alarm On
Signal On
•
The alarm on indicator and the Hourly Time Signal on indicator are shown on the
display in all modes while these functions are turned on.
Illumination
Two LEDs (light-emitting diodes) illuminate the face of the
watch for easy reading in the dark.
Illumination Precautions
•
Illumination may be hard to see when viewed under
direct sunlight.
•
Illumination automatically turns off whenever an alarm
sounds.
•
Frequent use of illumination runs down the batteries.
To illuminate the face of the watch
In any mode (except when a setting screen is on the display), press
C
to turn on
illumination.
•
When turning on illumination, press
C
and immediately release it. If you keep
C
held down too long, either of the operations described below will be peformed.
If you hold down
C
C
C
C
C
while in the Timekeeping Mode, Alarm Mode, or Hand
Setting Mode
The figures on the display will start to flash, which indicates the setting screen.
If this happens, press
C
again to exit the setting screen.
If you hold down
C
C
C
C
C
while in the World Time Mode
The DST setting will toggle between Standard Time and Daylight Saving Time,
which will affect the current time setting.
If this happens, hold down
C
again to toggle setting back to its original setting (if
necessary).
