Operation Guide 3422
E-39
Timekeeping
x
Resetting the seconds to
while the current count is in the range of 30 to
59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds
are reset to
without changing the minutes.
x
The year can be set in the range of 2000 to 2099.
x
The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
World Time
All World Time Mode times are calculated from the current Home City time in the
Timekeeping Mode using UTC time differential values.
x
The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
x
The UTC differential is a value that indicates the time difference between a
reference point in Greenwich, England and the time zone where a city is located.
E-38
Auto Return Features
x
If you leave the watch in the Alarm Mode for two or three minutes without performing
any operation, it automatically changes to the Timekeeping Mode.
x
If you leave a screen with fl ashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The
B
and
D
buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears fi rst.
E-37
Button Operation Tone
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
x
Even if you turn off the button operation tone, the alarms,
the Hourly Time Signal, the countdown alarm, and
stopwatch auto start all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down
C
to toggle the button operation tone
on ( not displayed) and off ( displayed).
x
Holding down
C
to turn the button operation tone on or off also causes the watch’s
current mode to change.
x
The mute
indicator is displayed in all modes when the button operation tone is
turned off.
Mute indicator
E-36
x
The following table shows the information that appears in graphic area A.
Mode
Graphic Area A
Timekeeping
Timekeeping Mode seconds
World Time
Timekeeping Mode seconds
Stopwatch (ST1 and ST2)
Sweeps from left to right
Countdown Timer
Sweeps from right to left
Alarm
No indication
x
In all modes, graphic area B shows the Stopwatch Mode (ST1) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
x
In all modes, graphic area C shows the Stopwatch Mode (ST2) minutes (one
segment each for 5 minutes, 10 minutes, etc.).
E-35
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Areas
There are three graphic areas named A, B, and C. The information shown in each
graphic area depends on the current mode.
Graphic area B
Graphic area C
Graphic area A
E-34
Warning!
x
Always make sure you are in a safe place whenever you are reading the watch
using the auto light switch. Be especially careful when running or engaged
in any other activity that can result in accident or injury. Also take care that
sudden illumination by the auto light switch does not startle or distract others
around you.
x
When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffi c accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down
B
for about three seconds to toggle the auto
light switch on (auto light switch indicator displayed) or off (auto light switch indicator
not displayed).
x
The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
x
In order to protect against running down the battery, the auto light switch turns off
automatically approximately six hours after you turn it on.
E-33
About the Auto Light Switch
While the auto light switch is enabled, illumination turns on whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes illumination to turn on.
x
Wear the watch on the outside of your wrist.
Parallel to ground
More than 40°
E-32
To illuminate the display
In any mode, press
L
to turn on illumination.
x
The above operation turns on illumination regardless of the current auto light switch
setting.
x
You can use the procedure below to select either 3 seconds or 5 seconds as the
illumination duration. When you press
L
, the illumination will remain on for about
3 seconds or 5 seconds, depending on the current illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down
A
until the
seconds start to fl ash, which indicates the setting
screen.
2. While the seconds are fl ashing, press
B
to toggle the
setting between 3 seconds ( ) and 5 seconds (
).
3. Press
A
to exit the setting screen.
E-31
Illumination
This watch has an LED (light-emitting diode) that cause
the entire display to glow for easy reading in the dark. The
watch’s auto light switch turns on illumination automatically
when you angle the watch for reading towards your face.
x
The auto light switch must be turned on (indicated by the
auto light switch indicator) for it to operate.
x
See “Illumination Precautions” (page E-40) for more
important information.
Auto light switch indicator
E-30
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
(east) and
B
(west) to
display the city code (time zone) whose Standard Time/
Daylight Saving Time setting you want to change.
2. Hold down
A
for about one second to toggle Daylight
Saving Time (
DST
displayed) and Standard Time (
DST
not displayed).
x
The
DST
indicator is on the display whenever you display
a city code for which Daylight Saving Time is turned on.
x
Note that the DST/Standard Time setting affects only
the currently displayed city code. Other city codes are
not affected.
DST indicator