Casio 3261 Operation Manual Download Page 11

Operation Guide 3261 3281

E-100

Bearing Sensor Precision:

Direction: Within ±10°

 

Values are guaranteed for a temperature range of –10°C to 40°C (14°F to 
104°F).

North pointer: Within ±2 digital segments

Temperature Sensor Precision:

±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)

Moon Data:

 Moon phase indicator for specific date, Moon age indicator

Other: Moon phase reversal

World Time:

 48 cities (31 time zones)

Other: Daylight Saving Time/Standard Time

Stopwatch:

Measuring unit: 1/100 second
Measuring capacity: 999:59' 59.99"
Measuring modes: Elapsed time, split time, two finishes

E-101

Countdown Timer:

Measuring unit: 1 second
Countdown start time setting range: 1 minute to 24 hours (1-hour increments and 

1-minute increments)

Alarms:

 5 daily alarms (four one-time alarms; one snooze alarm); Hourly Time Signal

Illumination:

 EL Backlight (electro-luminescent panel); Selectable illumination 

duration (approximately 1.5 second or 3 seconds); Auto Light Switch (Full 
Auto EL Light operates only in the dark)

Other:

 Battery power indicator; Power Saving; Button operation tone on/off

Power Supply:

 Solar cell and one rechargeable battery

Approximate battery operating time: 8 months (from full charge to Level 4) under 

the following conditions:

 Watch not exposed to light

 Internal timekeeping

 Display on 18 hours per day, sleep state 6 hours per day

 1 illumination operation (1.5 seconds) per day

 10 seconds of alarm operation per day

 10 digital compass operations per week

E-102

Frequent use of illumination runs down the battery. Particular care is required 
when using the auto light switch (page E-89).

L-1

L-2

City Code Table

City

Code

City

UTC Offset/

GMT Differential

PPG

PAGO PAGO

–11

HNL

HONOLULU

–10

ANC

ANCHORAGE

–9

YVR

VANCOUVER

–8

LAX

LOS ANGELES

YEA

EDMONTON

–7

DEN

DENVER

MEX

MEXICO CITY

–6

CHI

CHICAGO

NYC

NEW YORK

–5

City

Code

City

UTC Offset/

GMT Differential

SCL

SANTIAGO

–4

YHZ

HALIFAX

YYT

ST. JOHN’S

–3.5

RIO

RIO DE 

JANEIRO

–3

FEN

F.DE

NORONHA

–2

RAI

PRAIA

–1

UTC

0

LIS

LISBON

LON

LONDON

L-3

City

Code

City

UTC Offset/

GMT Differential

MAD

MADRID

+1

PAR

PARIS

ROM

ROME

BER

BERLIN

STO

STOCKHOLM

ATH

ATHENS

+2

CAI

CAIRO

JRS

JERUSALEM

MOW

MOSCOW

+3

JED

JEDDAH

THR

TEHRAN

+3.5

DXB

DUBAI

+4

City

Code

City

UTC Offset/

GMT Differential

KBL

KABUL

+4.5

KHI

KARACHI

+5

DEL

DELHI

+5.5

KTM

KATHMANDU

+5.75

DAC

DHAKA

+6

RGN

YANGON

+6.5

BKK

BANGKOK

+7

SIN

SINGAPORE

+8

HKG

HONG KONG

BJS

BEIJING

TPE

TAIPEI

L-4

City

Code

City

UTC Offset/

GMT Differential

SEL

SEOUL

+9

TYO

TOKYO

ADL

ADELAIDE

+9.5

GUM

GUAM

+10

SYD

SYDNEY

NOU

NOUMEA

+11

WLG

WELLINGTON

+12

 Based on data as of July 2010.

 The rules governing global times (GMT 

differential and UTC offset) and 
summer time are determined by each 
individual country.

Summary of Contents for 3261












Reviews: