Operation Guide 3134 3205
9
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes
Progress beeper: On
10'00"
Start Time
Reset Time
0'00"
1'00" 0'10"
2'00"
3'00"
4'00"
5'00"
Reset Period
Reset Period Beeper
Countdown
End Beeper
Reset Time Beeper
0'01"
0'02"
0'03"
0'04"
0'05"
0'06"
0'07"
0'08"
0'09"
0'10"
0'00"
To configure countdown timer settings
1. While the countdown start time is on the display
in the Countdown Timer Mode, hold down
E
until the countdown start time setting starts to
flash, which indicates the setting screen.
•
If the countdown start time is not displayed,
use the procedure under “To use the
countdown timer” to display it.
2. Press
D
to move the flashing in the sequence
shown below to select other settings.
Start
Time
Reset
Time
3. When the setting you want to change is flashing, use
A
and
C
to change
it as described below.
ll
ll
ll
ll
ll
lllll
ll
ll
ll
4. Press
E
to exit the setting screen.
•
The reset time setting must be less than the countdown start time setting.
To turn the progress beeper on and off
Pressing
B
while the countdown start time is on the display or while a
countdown timer operation is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
displayed) and off
(
displayed).
Setting
Start Time
Reset Time
Screen
Button Operations
Use
A
(+) and
C
(–) to change the setting.
•
You can set a start time in the range of 1 to 60
minutes in 1-minute increments.
Use
A
(+) and
C
(–) to change the setting.
•
You can set a reset time in the range of 1 to 5
minutes in 1-minute increments.
To use the countdown timer
In the Countdown Timer Mode, press
A
to start
the countdown timer.
•
The countdown timer measurement operation
continues even if you exit the Countdown Timer
Mode.
•
The table below describes button operations you
can perform to control countdown operations.
llllllllllll
Stopwatch
The stopwatch lets you measure elapsed time,
split times, and two finishes.
•
The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
•
The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.
•
The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.
•
All of the operations in this section are
performed in the Stopwatch Mode, which you
enter by pressing
D
.
Minutes
Current time
1/100 second
Hours
Seconds
J
J
J
J
J
J
J
J
J
J
J
First runner
finishes.
Display time
of first runner.
J
Elapsed Time
A
A
A
A
C
Start
Stop
Re-start
Stop
Clear
Split Time
A
C
C
A
C
Start
Split
Split release
Stop
Clear
Two Finishes
A
C
A
C
C
Start
Split
Stop
Split release
Clear
Display time of
second runner.
Second runner
finishes.
(
SPL
displayed)
To measure times with the stopwatch
World Time
World Time displays the current time in 33 cities
(29 time zones) around the world.
•
If the current time shown for a city is wrong,
check your Home City time settings and make
the necessary changes.
•
All of the operations in this section are
performed in the World Time Mode, which you
enter by pressing
D
.
To view the time in another city
In the World Time Mode, use
A
(east) and
C
(west) to scroll through city codes (time zones).
•
For full information on city codes, see the “City
Code Table”.
Timekeeping
Mode time
Current time in the zone
of the selected city code
City code
To toggle a city code time between Standard Time and Daylight
Saving Time
1. In the World Time Mode, use
A
(east) and
C
(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
E
to toggle between Daylight
Saving Time (
DST
indicator displayed) and
Standard Time (
DST
indicator not displayed).
•
The
DST
indicator appears on the display
whenever you display a city code for which
Daylight Saving Time is turned on.
•
You cannot toggle between Daylight Saving Time and Standard Time if the
displayed city code is
UTC
.
•
Note that the DST/Standard Time setting affects only the currently
displayed city code. Other city codes are not affected.
DST indicator
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown
reaches zero, and at zero. The first five beeps (seconds 10 through 6) are
higher pitched than the final five beeps (seconds 5 through 1). The watch
emits a longer beep to signal when the countdown reaches zero.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and
a reset period beeper.
•
Note that the reset time beeper and reset period beeper operate only while
the progress beeper is turned on. For more information, see “To turn the
progress beeper on and off”.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. The watch
beeps each second of the final 10 seconds before the countdown reaches the
reset time.
Reset Period Beeper
The reset period is the portion of the countdown between the reset time and
zero. While timing is in the reset period, the watch will beep four times at the
top of each minute and 10 seconds before the end of the countdown.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset
time
Start the countdown from the displayed reset time
Do this:
Press
A
.
Press
A
again.
While the countdown is
stopped, press
C
.
Press
C
.
Press
A
.
