manualshive.com logo in svg

Casio 3043, Operation Manual, Page: 8 / 14

Share
Download
Casio 3043 Operation Manual Download Page 8

Operation Guide 3043

8

•

When the currently selected time zone is one that includes mostly ocean, a
value indicating the zone’s Greenwich Mean Time differential appears in
place of a city code.

•

If the current time shown for a city is wrong, check your Home City time
settings and make the necessary changes.

To toggle a city code time between Standard Time and Daylight
Saving Time

1. In the World Time Mode, use 

C

 (east) and 

A

(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.

2. Hold down 

E

 to toggle between Daylight

Saving Time (

DST

 indicator displayed) and

Standard Time (

DST

 indicator not displayed).

•

The 

DST

 indicator appears on the display

whenever you display a city code for which
Daylight Saving Time is turned on.

•

You cannot toggle between Daylight Saving Time and Standard Time if the
displayed city code is 

GMT

.

•

Note that the DST/Standard Time setting affects only the currently
displayed city code. Other city codes are not affected.

Stopwatch

The stopwatch lets you measure elapsed time,
split times, and two finishes.

•

The display range of the stopwatch is 9 hours,
59 minutes, 59.99 seconds.

•

The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.

•

The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.

•

Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.

•

All of the operations in this section are
performed in the Stopwatch Mode, which you
enter by pressing 

D

.

Minutes

Seconds

1/100
second

Timekeeping
Mode time

Hours

First runner
finishes.
Display time
of first runner.

Display time of
second runner.

Second runner
finishes.

Elapsed Time

C

C

C

C

A

Start

Stop

Re-start

Stop

Clear

Split Time

C

A

A

C

A

Start

Split

Split release

Stop

Clear

(

sj

 displayed)

Two Finishes

C

A

C

A

A

Start

Split

Stop

Split release

Clear

To measure times with the stopwatch

Countdown Timer

You can set a countdown timer start time in the
range of one minute to 60 minutes. An alarm
sounds when the countdown reaches zero. An
auto-repeat feature causes the countdown to
restart automatically when the end of a
countdown is reached, and a progress beeper
signals the progress of the countdown.

•

All of the operations in this section are
performed in the Countdown Timer Mode,
which you enter by pressing 

D

.

Configuring the Countdown Timer

The following are the settings you should
configure before actually using the countdown
timer.

•

Countdown start time

•

Auto-repeat on/off

•

Progress beeper on/off

Timekeeping
Mode time

Countdown start time

You can set a countdown start time in the range of one minute to 60 minutes,
in one-minute increments.

Auto-repeat

Whenever zero is reached, the watch beeps and auto-repeat automatically
restarts the countdown from the countdown start time you set. When the
countdown reaches zero while auto-repeat is turned off, the watch will beep
and then display the countdown start time (without restarting the countdown).
Auto-repeat will repeat up to 10 times.

Progress Beeper

When the progress beeper is turned on, the watch beeps at minute 10, 5, 4,
3, 2, and 1 of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2, and
1 of the final minute of the countdown.

To configure countdown start time and auto-repeat settings

1. While the countdown start time is on the

display in the Countdown Timer Mode, hold
down 

E

 until the minute setting of the

countdown start time starts to flash, which
indicates the setting screen.

•

If the countdown start time is not displayed,
use the procedure under “To use the
countdown timer” to display it.

2. Press 

D

 to toggle between the countdown

starting time setting screen and the auto-
repeat setting screen.

3. Perform the following operations, depending on which setting is currently

selected on the display.

•

While the minute setting is flashing, use 

C

 (+) or 

A

 (–) to change it.

•

While the auto-repeat on/off setting (

 or 

) is flashing on the

display, press 

C

 to toggle auto-repeat on (

) and off (

).

4. Press 

E

 to exit the setting screen.

l l l l l l

ll

ll

lll

ll

ll

ll

ll

ll

l l

To turn the progress beeper on and off

Pressing 

A

 while the countdown start time is on

the display or while a countdown timer operation
is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
displayed) and off (

  not displayed).

To use the countdown timer

Press 

C

 while in the Countdown Timer Mode to start the countdown timer.

•

When the countdown reaches zero, the alarm sounds for five seconds or
until you stop it by pressing any button.

•

Press 

C

 while a countdown operation is in progress to pause it. Press 

C

again to resume the countdown.

Progress beeper on
indicator

•

The countdown timer operation continues even if you exit the Countdown
Timer Mode.

•

To stop a countdown operation completely, first pause it (by pressing 

C

),

and then press 

A

. This returns the countdown time to its starting value.

•

Frequent use of auto-repeat and the alarm runs down the battery.

Minutes

To view the time in another city

In the World Time Mode, use 

C

 (east) and 

A

 (west) to scroll through city

codes (time zones).

World Time

World Time digitally displays the current time in
30 cities (29 time zones) around the world.

•

For full information on city codes, see the “City
Code Table”.

•

All of the operations in this section are
performed in the World Time Mode, which you
enter by pressing 

D

.

Timekeeping Mode time

Current time in the zone
of the selected city code

Seconds

Summary of Contents for 3043















Reviews:

No comments