Operation Guide 3040
7
3.
Configure the setting that is flashing.
To set the start time hours and minutes
Use the
D
D
D
D
D
(+) and
B
B
B
B
B
(–)
buttons to change the
hour and minute settings.
•
Holding down either button
changes the setting at high
speed.
•
To configure the setting to
countdown 24 hours, set the
start time as 0:00.
To select the timer type
Press the
D
D
D
D
D
button to
toggle between the auto
repeat timer and repeat
timer.
•
“ON” indicates the auto repeat
timer while “OFF” indicates
the repeat timer.
4.
When all of the settings are the way you want, press the
A
A
A
A
A
button to exit the setting screen.
•
The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
•
The auto repeat indicator (
) appears on the display while
the auto repeat timer is turned on.
(+)
(–)
Auto Repeat
Timer
You can set the start time of the timer in units of one minute in the
range of 1 to 24 hours. The watch beeps for 10 seconds when the
end of the countdown is reached. Turning on the watch’s auto
repeat timer feature causes the countdown to restart from the start
time whenever the end of the countdown is reached.
Timer Types
You can use either of the two settings describe below to configure
timer settings.
•
For information about selecting the timer type, see “To
configure timer settings”.
Repeat Timer
With the Repeat Timer, the timer stops when the end of the
countdown is reached. After about 10 seconds, the original start
time re-appears on the display.
●
Auto Repeat Timer
With the auto repeat timer, the timer automatically resets the start
time and continues timing when the end of the current countdown
is reached.
•
The countdown repeats up to eight times, or until you stop it
manually.
❚
To configure timer settings
1.
While the current starting
time is displayed in the
Timer Mode, press the
A
A
A
A
A
button.
•
The hour digits start to flash
on the display. This is the
setting screen.
2.
Use the
C
C
C
C
C
button to move
the flashing to the setting
you want to change.
•
Each press of
C
moves the
flashing between the settings
as shown below. Move the
flashing to the digits you want
to change.
Timer Type
Minute
Hour
Hour
Minute
Using the Timer
Use the
C
C
C
C
C
button to enter the Timer Mode as shown under “Modes
and Indicators”.
❚
To use the countdown timer
Press the
D
D
D
D
D
button to interrupt time calibration signal
reception.
•
Each press of the
D
button starts or stops the stopwatch.
•
The time counts down in 1/10-second steps.
(Reset)
(Start/Stop)
1/10 second
Hour, Minutes Seconds
•
Pressing the
A
button while the countdown is stopped
displays the reset time.
•
Holding down the
D
button for about two seconds while a
countdown either is ongoing or stopped will reset the timer
to its start time.
•
Pressing the
D
button again while the countdown is
stopped restarts the countdown.
Time Up Beeper
The watch beeps for 10 seconds when the end of the countdown
is reached.
❚
To stop an alarm
Pressing any button while the beeper is sounding stops it.
The stopwatch measures elapsed time in units of 1/10 second up
to 23 hours, 59 minutes, 59.9 seconds (24 hours). When the
maximum limit is reached, the elapsed time returns to zero
automatically and timing continues from there.
Using the Stopwatch
In the Stopwatch Mode, press the
D
D
D
D
D
button to start and stop
the stopwatch.
•
Each press of the
D
button starts or stops the stopwatch.
(Split/Reset)
(Start/Stop)
1/10 second
Hour, Minutes Seconds
•
Pressing the
A
button while an elapsed time operation is in
progress will freeze the current time on the display and
continue timing of the next split internally. This condition is
indicated by the “SPL” (split) indicator on the display.
Changing to another mode while a split time is displayed
cancels the split time operation.
•
Pressing the
A
button while the stopwatch is stopped will
reset stopwatch to all zeros.
•
Holding down the
D
button for about two seconds while
the stopwatch either is performing an elapsed time
operation or stopped also will reset it to all zeros.
❚
To measure elapsed time
Stop
Reset
Start
Cumulative Time Measurement
Pressing the
D
button to restart the stopwatch without resetting it
to all zeros will resume elapsed time measurement from where it
was last stopped.
❚
To measure split times
Split
Release Split
Reset
Stop
Start
Split Indicator
Split Time Screen
Release
Split
❚
To time 1st and 2nd place finishers
Start
2nd Finisher
Reset
1st Finisher
(Displays time
of 1st finisher.)
Displays
time of 2nd
finisher.
Using the Stopwatch
Use the
C
C
C
C
C
button to enter the Stopwatch Mode as shown
under “Modes and Indicators”.
