cashco PGR-2 Installation, Operation & Maintenance Manual Download Page 14

Page: 14 / 16

Cashco, Inc.
P.O. Box 6
Ellsworth, KS 67439-0006
PH (785) 472-4461
Fax (785) 472-3539
www.cashco.com
email: [email protected]
Printed in USA IOM-PGR-2

Cashco do Brasil, Ltda.
Al.Venus, 340
Indaiatuba - Sao Paulo, Brazil
PH +55 11 99677 7177
Fax. No.
www.cashco.com
email: [email protected]

Item No.

Description

60.1

Body

60.2

Spring Chamber

60.3

Pressure

Plate

60.4

Pusher

Plate

60.5

Spring

Button

60.6

Body

Cap

60.7

Piston

Spring

60.8

Adjusting

Screw

60.9

Lock

Washer

60.10

Nut (Pressure Plate)

60.11

Nut

60.12

Diaphragm

60.13

O-ring

60.14

Piston

60.15

Range

Spring

* Recommended Spare Parts

Inlet

Outlet

Vent

Cashco GmbH
Handwerkerstrasse 15
15366 Hoppegarten, Germany
PH +49 3342 30968 0
Fax. No. +49 3342 30968 29
www.cashco.com
email: [email protected]

Summary of Contents for PGR-2

















Search results

Summary of Contents for PGR-2

Reviews:

Related manuals for PGR-2

Brands by name

Popular brands

cashco PGR-2, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for PGR-2

Reviews:

Related manuals for PGR-2

Brands by name

Popular brands